injecting system 中文意思是什麼
injecting system
解釋
注入系統-
Design of temperature control system of plastic injecting machine
注塑機溫度控制系統設計 -
The calibrating technology is mainly divided into two groups : the off - line ones and the on - line ones. the former one is now widely used in the monopulse system to calibrate the amplitude and phase imbalances between the sum and difference channels by injecting test signals
離線校正的方法是現階段單脈沖雷達系統進行和差通道幅相校正採用的主要方法，它通過注入測試信號的方法來得到對誤差接收通道幅相特性的估計。 -
When injecting samples, chromatographic column should be completely flushed and balanced with mobile phase ; if the system applicability is not up to regulation, or if filling agents are damaged, replace with new similar chromatographic column for analysis ; if operation according to procedures can not reach scheduled separation due to existence of certain difference between degree of bond of chemically bonded - phase of similar filling agents and performance, another brand of similar chromatographic column can be used for test
3進樣前，色譜柱應用流動相充分沖洗平衡，如系統適用性並不符合規定，或填充劑已損壞，則應更換新的同類色譜柱進行分析，由於同類填充劑的化學鍵合相的鍵合度及性能等存在一定差異，往往依法操作達不到預定的分離時，可更換另一牌號的同類色譜柱進行試驗。 -
The underground mobile colloid - injecting system for fireproofing and fire extinguishing
井下移動式防火和滅火注膠系統 -
Feasibility analysis on automatic injecting ammonia control system in thermodynamic system
淺談熱力系統除鹽水自動加氨控制的可行性 -
There has been much progress in recent years in modernising the banking system, through commercialising it, cleaning up the stock of bad debts and stemming the flow of new ones, injecting capital into the banks, upgrading corporate governance and strengthening banking supervision
內地近年在銀行體系現代化方面取得不少進展，例如銀行商業化清理積存的壞帳遏止新壞帳形成給銀行注入資本提升公司治理水平，以及加強銀行監管。 -
Abstract : the injecting molding machine expert system ( imm es ) is discussedin this paper
文摘:介紹了在注塑機方面專家系統的開發與應用，著重描述了注塑機專家系統的推理機制。 -
Through theoretical analysis, experiment on site and numerical simulation, the characteristic of goal - water - gas system was analyzed during injecting water, and the mechanics properties, stress and strain state of coal and quantity of gas emission were studied
摘要通過理論分析、現場實驗及數值模擬等手段，分析了注水過程中煤水瓦斯體系特徵，研究了注水對煤的力學性質、應力和變形狀態以及對瓦斯湧出量的影響。 -
Technical features of chemical injecting system for inner cooling water of 660mw generators in hanfeng power plant
發電機組內冷水系統加藥控制技術特點 -
The principle of the fault distance measurement for small current grounding system by injecting dual frequency signal are discussed from many aspects such as the method and the characteristic of the signal, the test of the signal, the method of the line select, the algorithm of the fault distance measurement, and the method of the fault location, etc. the task adopts this kind of principle, in which the signal injection is completed by the coupling between the power source and the pt
在詳細地說明以上三種測距演算法的基本原理后，分析各種演算法的優缺點，從注入信號的方法、特徵，注入信號的檢測，接地選線的方法，故障測距的演算法，及故障定位的方法等多個方面，論述了本課題採用的應用於小電流接地系統的雙頻信號注入式測距原理。其中，信號的注入由功率源通過電壓互感器（ pt ）耦合來完成。 -
Injecting control system of fuel with ke - jetronic mfi
系統噴油量的控制 -
The deficiencies of the off - line methods are as follows : it is not an adaptive method so it cannot change when the system parameter changes ; it is, to some degree, depend on the form of the injecting signal
離線校正的缺點是適應性不強，它不能對變化的誤差系統進行實時跟蹤，並且它很依賴于注入測試信號的形式。 -
By pre - mixed methanol through intake manifold on a diesel engine car, the fuel economical performance and acceleration performance are researched, and an electronic control system is developed to control the injecting quantity of pre - mixed methanol
摘要研究了進氣預混甲醇柴油汽車的經濟性性能和加速性能，並開發了控制甲醇噴射的電控裝置。 -
And quantity of water will be adjusted by the system when engine works in the water injecting mode
本文利用該系統對4135g型柴油機進行試驗，得出了良好結論。
分享友人