injection heating 中文意思是什麼

injection heating 解釋
注入加熱
  • injection : n. 1. 注射。2. 注射劑，注射液，針藥，灌腸（藥）。3. 充滿，注滿。4. 【醫學】充血。5. 【機械工程】噴射。6. 【宇宙空間技術】（衛星等的）入軌，射入軌道，射入軌道的時間[地點]。
  • heating : adj. 1. 加熱的；供熱的。2. 刺激的。n. 1. 加熱；供暖；（建築物的）暖氣裝置。2. 白熾，灼熱。
  1. Syringe and injection needle - render the syinges and needles pyrogen - free by heating at 250 for not less than 30 minutes

    注射器和注射針頭?在250攝氏度下加熱至少半小時使注射器和針頭無帶熱源質。
  2. Plastic injection mould, coolant passages, eject pin and electrical heating holes

    塑膠射出模具?冷卻水孔、射梢孔及電熱孔
  3. Analytical solution for steam heating system of hollow sucker rod and optimal design of injection parameters

    空心抽油桿注蒸汽數學模型的解析解及其參數優化
  4. Neutral beam injection ( nbi ) heating is one of the main auxiliary heating methods in controllable nuclear fusion experiment

    中性束注入加熱是可控核聚變主要的輔助加熱方式之一。
  5. It is very significant for the research of nucleus fusion in resolving energy sources shortage, and neutral beam injection ( nb1 ) heating is one of the important assistant heating methods in nucleus fusion

    核聚變研究在解決當今能源短缺問題上具有十分重大的意義，中性束注入加熱是核聚變中重要的輔助加熱方式之一。
  6. The article primary introduces composing of ht - 7 neutral beam injection ( nbi ) system, then mainly analyzes gas target thickness, that is pressure distribution of neutralizer gas cell, one of factors which affect heating efficiency of nbi

    本文首先介紹了ht - 7中性束注入（ nbi ）加熱系統的組成，然後對影響中性束注入加熱效率因素之一的氣體靶厚度即中性化室的壓力分佈進行了重點分析。
  7. Molding steps : mold opening / closing, heating injection and knocking out

    按成型步驟:可分為開鎖模，加熱，射出，頂出四個過程
  8. Research and application of explosive deflagration ash - cleaning technology on steam injection boiler for heavy oil heating recovery

    稠油熱采注汽鍋爐弱爆炸除灰技術應用研究
  9. This thesis gives a fundamental quantitative analysis of the cycle of recuperative gas turbine cogeneration with water injection and mainly discusses the influence of water injection ratio and pressure ratio on the specific power and the amount of heating

    本論文對功熱並供回熱注水燃氣輪機熱力循環進行了基本定量分析。主要分析了注水率和壓比對比功和供熱量的影響。
  10. The hot runner series makes the plastics in the hot runner from the nozzle of a plastics injector to the inlet of cavity must be always kept at such a molten state by means of heating that you just pick out the product, there is no need for you to take the condensing stuffs from the injection system as the mould cavity is operated

    說明:熱流道系列用加熱的方法使從注塑機噴嘴到型腔入口為止這一段流道中的塑料一直保持熔融狀態，在開模時只需取出產品，而不必取澆注系統凝料。
  11. Plastics piping and ducting systems - injection - moulded thermoplastics fittings - methods for visually assessing the effects of heating

    塑料管和管道系統.噴射鑄造熱塑配件.熱效應直觀評估法
分享友人
分享到 Line

分享到臉書