injector valve 中文意思是什麼

injector valve 解釋
噴油嘴針閥
  • injector : n. 1. 注射者；注射器，針管。2. 【機械工程】噴射器，噴注器，噴霧器，噴頭。
  • valve : n 1 【機械工程】閥，活門，舌門；汽門。2 【解剖學；動物學】瓣，瓣膜；（貝）殼瓣；【植物；植物學】...
  1. For the valve with the metal to metal seal, there is grease injector outside of it, grease gets into the sealing face through the injector and the seat ring to have the valve up to null leak

    金屬對金屬密封的閥門，閥體外部設有注油脂結構，油脂通過注脂器、閥座進入閥門密封面，使閥門達到零泄漏。
  2. The contents of the thesis are as follows : ( 1 ) all the contents : magnetism sense fuel injector is designed. needle valve lift signal, rotation speed signal and pressure signal are collected and processed. circuit is designed. programme is programmed. ( 2 ) contents studied : the item is completed

    本課題的研究內容有: （ 1 ）本課題所要研究的內容包括:磁感噴油器的設計;針閥升程信號、主軸轉速信號、噴油壓力信號的採集與處理;系統硬體電路的設計;軟體編程等。
  3. Valve type injector

    閥式噴油器
  4. After analyzing the performance of lpg, this paper provided an electronic controlling lpg fuel supply system to fulfill the function of dual fuel on the diesel engine. the system use the philip 87c552 single - chip microprocessor as the cpu of the electronic control unit, with high speed valve as injector. the hardware development was discussed in detail in the paper

    本文在對lpg性能進行介紹分析的基礎上，開發了一套電控lpg燃料供給系統，實現了原柴油機的雙燃料運行；系統中的lpg供給採用高速電磁閥，系統控制硬體以飛利浦p87c552單片機為核心，配合合理的輸入輸出介面電路。
  5. While unscrewing the injector button head, a second wrench must be used to assure that the injector body is not loosened from the main valve

    在擰松注入器圓頭螺栓時，要用第二個扳手固定住注入器，防止其從主閥門上松落下來。
  6. The original pump - line - nozzle injection system was found to be not well suited to alternative fuels. this paper introduces a novel electronically controlled pump - rail - valve - injector fuel injection system

    但液化代用燃料在發動機應用最大的困難是與常規泵-管-嘴噴射系統的不匹配。
  7. Pacific valves ' unique injector has a double ball check protection against leakage and a positive shut - off internal valve

    美國太平洋閥門獨特的注入器具有雙球止回保護，防止泄露，並保護閥門內部活動部件。
  8. All these characteristic can satisfy the demand of the factory. by using this system can change the laggard situation of the manual separation of injector valve and orifice

    能滿足噴油嘴偶件生產廠家對噴油嘴偶件針閥、針閥體自動分選精度，速度的要求以及對成本投入的要求，改變手工分選的落後局面。
  9. The project is funded by the anhui oil pump and oil nozzle factory. the aim of this project is to develop the automatic separation system of injector valve and orifice, based on the pneumatic sensor and the mcu

    本課題來源於安徽油泵油嘴廠，目的是研究一套價格為企業所接受的基於氣動傳感器並以單片機進行數據處理和控制的噴油嘴偶件針閥和針閥體自動測量分選系統。
  10. Pneumatic and automatic separator of injector valve and orifice is based on pneumatic measurement and 8051 mcu, which is used for data processing and control. it can automatically separate injector valve and orifice, whose nominal size is 6 and tolerance is + 10u, with the interval of 1u, accuracy of 0. 5u and speed of twenty pieces per minute around. the automatic separation system of injector valve and orifice has low cost, high separation accuracy, high separation speed and easy operation

    使用氣動噴油嘴偶件針閥、針閥體自動分選系統能實現對公稱尺寸為6 、公差為10的噴油嘴偶件針閥、針閥體按1分選間隔、 0 . 5分選精度的自動分選，分選時的速度可達每分鐘20件左右。
  11. The injector button head must be unscrewed one half turn to open the internal valve before injecting grease

    在注入潤滑油之前，注入器圓頭螺栓必須擰松半圈，打開閥門內部部件通道。
  12. The system has others virtues, such as wide fuel adaptability, little fluctuation of pressure, good seal performance, etc. the injector of direct injection is assembled from electronic controlled valve and diesel injector, and it is used in the experiment

    研究了多種燃料供應方式下的燃料供應系統，其中缸內噴射系統創造性地採用液壓增壓方式，其具備燃料適應性廣、噴射壓力可調（ 2 12mpa ） 、壓力波動小、密封性好等優點。
分享友人
分享到 Line

分享到臉書