inlet section 中文意思是什麼
inlet section
解釋
入口斷面-
Cross - section design of a controllable hypersonic inlet. the research is being done at the nanjing university of aeronautics and astronautics
南京航空航天大學正在進行一個可控高超音速進氣道斷面設計研究。 -
Based on the temperature field obtained by the thermal analysis, a parametric analysis is conducted to investigate the interlaminar stress at the interface between the composite and the thermal barrier in the cross - section of the inlet duct, using the commercial finite element software ansys
在熱分析的基礎上，採用ansys有限元軟體計算了復合材料進氣道截面在假設工況下的應力場，為碳纖維纏繞復合材料進氣道熱防護方案的設計提供了實用的參考依據。 -
In order to investigate the unsteady flow frequency domain performances of an axial flow compressor at different mass flow, rotating speed and blade row spacing, plus inlet flow distortion, and considering aerodynamic characteristics and stability of the compressor, the low speed research compressor ( lsc ) at college of energy and power in nuaa is used to carry out the experiment studies. a large amount of test data has been gained through dynamic pressure transducers embedded in the stator blades at the tip, middle and hub section, then fast fourier transform algorithm ( fft ) is applied to calculate the frequency data
為探討軸流壓氣機在工作流量、工作轉速及動?靜葉排軸向間距變化時的葉片排流場非定常頻譜特性變化規律，並耦合進氣畸變的影響，同時與壓氣機氣動性能和氣動穩定性相關聯，作者利用南京航空航天大學能源與動力學院的低速大尺寸軸流壓氣機（ lsc ）試驗器，採取在靜子葉片表面埋入動態壓力傳感器的實驗方法，對葉尖、葉中和葉根三個截面的動態壓力進行了測量，獲得了大量的可靠的實驗數據。 -
Based on the review, the fluid flow and heat transfer in the curved circular and rectangular pipes have been researched by employing perturbation method and numerical simulation with a physical model under the rotational orthogonal curvilinear coordinate in a rotating curvilinear pipe with multi - parameters. we firstly analyzed the fully developed fluid flow and heat transfer, mixed convection heat transfer, the development of flow and heat transfer in the inlet in different cross section ( circular, elliptical, annular and rectangular crossection ). the variations of the secondary flow, axial velocity, distribution of temperature, the friction force on the wall, the ratio of friction factor as well as the nusselt number with different dimensionless parameters had been examined in detailed
本文在總結和分析了一個世紀以來有關曲線管道流動和換熱特性的研究成果的基礎上，以旋轉正交曲線坐標系統下的多參數旋轉螺旋管道中的對流傳熱為物理模型，通過攝動方法和有限體積法，首次對各種截面（圓截面、橢圓截面、環形截面、矩形截面）旋轉曲線管道內充分發展流動的流動結構和傳熱特性（包括耦合對流傳熱特性）以及旋轉曲線管道開口段發展流動的流動結構和換熱特性進行了系統的數值模擬和理論分析，詳細討論了各種無量綱參數對管道內軸向速度分佈、二次流結構、溫度分佈、壁面摩擦力、摩擦系數比以及管道nusselt數的影響，獲得了若干創新性成果。 -
The velocity - coefficient method was used to design a 180mm diameter impeller with five single - arc - cylinder blades. the exit angle and inlet angle of the segment are 35. 1 and 36. 0 in degrees respectively. the shape volute ' s cross - section is the rectangle
該葉輪採用速度系數法設計，轉輪外徑180mm ，共有5張單圓弧圓柱形葉片，其出口安放角、進口安放角分別為35 . 1度、 36 . 0度。 -
There are several important issues to that attention should be paid in the design of test bed, such as the measurement of the temperature difference between the inlet and outlet of test section and the temperature of cooling water in the inlet and outlet of condensing tubes, filled volume of the steam boiler and its level control, the determination of the natural acting head of high temperature tank and design of the cooling water flow of measuring tank
試驗臺由高溫工質自然循環子系統、冷卻水機械循環子系統和計算機監測控制子系統構成，試驗段進出口溫差及冷凝管進出口溫度的測試、蒸汽鍋爐充注量及液位控制、高溫水箱自然作用水頭的設計、冷卻水流量計量水箱的設計等是試驗臺設計中值得重視的問題。 -
The calculation formulas for velocity coefficients 2 and 5 for the throat and throat inlet section were deduced from the theoretical research on the velocity coefficients in time - averaged basic equations by use of the unsteady momentum equation and time - averaged value calculation method
摘要運用非恆定的動量方程和時均值計算方法，對脈沖液體射流泵時均值基本方程中的流速系數進行了理論研究，推導出了喉管和喉管進口段流速系數2和5的計算式。
分享友人