inner-cooling 中文意思是什麼

inner-cooling 解釋
內部冷
  • inner : adj （superl innermost inmost）1 內部的 （opp outer）。2 思想的，精神的；內心的，秘密的。n 1 內部...
  • cooling : n. ,adj. 冷卻（的）。
  1. Under the assumption that the inner surface of stator sleeve and outer surface of rotor are smooth, taking the fact into account that the temperature of stator sleeve of evaporation cooling motor keeps almost the same, horizontal evaporation cooling motor is simplified as a physical model of two coaxial sleeves, with outer sleeve ( the stator ) holds still and keep at constant temperature and inner sleeve ( the rotor ) is rotating and heated

    本文通過數值和實驗手段研究了臥式蒸發冷卻電機楔形氣隙中的流體流動、傳熱現象。本文在定子套筒和轉子表面光滑的假設下，針對蒸發冷卻電機定子套筒壁面基本恆溫的特點，將實際蒸發冷卻電機簡化為同軸套筒內筒加熱旋轉、外簡靜止定溫的物理模型。
  2. 4 ) in a pre - swirl rotator - stator cavities with discrete pre - swirl nozzles and blade - cooling entry holes, the influences of pre - swirl angle and flow parameter on the flow and heat transfer characteristics were numerically investigated. the correlation for average nusselt number vs rotating reynold number or non - dimensional mass flowrate were established. the results show that : advantage of per - swirl inflow is the effect of cooling the blade - cooling entry holes ; pre - swirl inflow increases heat transfer in rotating disk of pre - swirl chamber ; as pre - swirl angle increases, local nusselt number decreases in pre - swirl chamber ; the temperature of stator of inner rotator - stator chamber and per - swirl chamber decreases as rotating reynold number increases ; when the axial mass flowrate maintains constant, heat transfer in the rotating disk of inner rotator - stator cavities does n ' t change as per - swirl mass flowrate increases, while heat transfer in the rotating disk of per - swirl chamber increases ; when the pre - swirl mass flowrate maintains constant, change of the axial mass flowrate has effect on the whole cavity

    結果表明，預旋進氣的優點在於增強了葉片冷卻孔附近的對流換熱效果，局部努謝爾數隨預旋角的增大而有所減小；隨旋轉雷諾數的增加，不論是內轉靜腔室還是預旋腔室的靜盤上的溫度都不同程度的降低：當軸向中心進氣質量流量不變時，隨預旋進氣的質量流量增加，內轉靜腔室的轉盤盤面上的換熱基本沒有變化，而預旋腔室的轉盤盤面上的換熱效果增強；當預旋進氣質量流量不變時，軸向中心進氣的質量流量的改變對整個盤腔都有影響。
  3. Abstract : the distribution of cooling air which is in the grille - brick of the inner combustion hot air stove has been simulated with three dimension turbulent mathematical model so as to find a method which is used to improve the distribution of cooling air in hot air stove. the influence of differential horizontal plates on the distribution of cooling air is discussed. the results show that original big circle round field of flow in the pillar - cavity is changed into full one - way field of flow and edges gas flow, at the same time, is increased by horizontal plates. there is a different function with horizontal plates and vertical plates. to make the uniform distribution of cooling air in the hot air stove, it is necessary that horizontal plates and vertical plates are used in a combined way

    文摘:應用紊流三維數學模型模擬內燃式熱風爐內冷風在格子磚柱中的分佈，尋求改善其分佈的途徑.討論了加設不同布置的水平導流板對氣流分佈的影響.模擬結果表明，在支柱空腔內加設水平導流板改變了原有大迴旋流場，使迴旋流變成大面積的單向流.通過在支柱空腔內加設水平導流板可以發展邊緣氣流，這恰好與加設豎直導流板的作用相反，水平導流板和豎直導流板的結合使用有望實現冷風在格子磚柱中的均勻分佈
  4. One cooling method that has gained increasing importance is endwall film - cooling, where coolant air is discharged though discrete holes in the inner and outer endwalls of a turbine blade passage. after leaving the holes, the coolant forms a protective layer between the hot mainstream gas and the surface that is to be protected

    目前廣泛採用的一種重要冷卻方法是渦輪葉柵端壁氣膜冷卻，該方法中冷空氣穿過渦輪葉片上內外端壁離散冷卻孔進行交換，且冷空氣流經冷卻孔后在主流熱空氣與被保護表面之間形成保護層。
  5. The blade inner channel cooling is a complex convection - conduction coupling problem. this thesis build a three - dimension. compressible turbulence model, and give a general solve method. with the geometrical model of the glossily rectangle straight channel, the rectangle straight channel with in - line arrays disturb plates, the rectangle straight channel with staggered arrays disturb plates, the rectangle straight channel with slant disturb plates, this thesis compute the flow and heat transfer condition when the cold air path though these channels, and gain the temperature field, pressure field, velocity filed, in addition. this thesis also analyze the influence of the different channel height, the different channel materials, the different channels, and gain the function relation between he nusselt number, friction factor and reynolds number. this thesis is emphasis on the new heat transfer enhancement structure, that is, disturb plates, with the comparison with the glossily channel and channel with pin fins, the heat transfer enhancement effect of the former is better, and the conclusion can be used in the design of aircraft blade

    葉片內部通道冷卻是一個復雜的對流?導熱耦合傳熱問題，本文在分析葉片內部通道冷卻的流動與傳熱情況的基礎上，建立了三維、可壓縮紊流的物理模型，得到了通用的求解辦法；利用不帶擾流片的矩形直通道、帶順排擾流片矩形直通道、帶叉排擾流片、帶傾斜擾流片的矩形直通道的幾何模型，計算了冷卻空氣通過這幾種通道時的流動與換熱情況，得到了各種不同情況下計算區域的溫度場、壓力場、速度場；在此基礎上分析了不同的通道高度、不同的葉片通道材質對葉片內部通道冷卻的影響，並整理得到了各種通道形式下，努謝爾數和阻力因子與雷諾數的函數關系；本文重點研究了新型的葉片內部通道冷卻強化傳熱措施?帶擾流片的內部冷卻通道的強化傳熱效果，通過與光滑矩形直通道、帶針肋通道的冷卻效果的比較，表明了這種新型鮚構的優勢，對于葉片內部通道冷卻結構的設計可以起到指導的作用。
  6. Changing temperature velocity in inner barrel is not a stable constant, and it will vary with advancement of measuring from time to time, thus cooling emendation quadrature model is established to compensate temperature dissipation

    提出以內外桶溫差導致的量熱系統溫度變化的速度對主期測量時間進行積分的冷卻校正計算模型。
  7. The blade inner channel cooling is very important in the design of turbine blade, with the ever - increasing inlet temperature, the new heat transfer enhancement structures of higher performance are demanded. because of the complexity of the flow and heat transfer of the blade inner channel cooling, the numerical modulation is superior to the experiment. this thesis studied the blade inner channel cooling with the method of numerical modulation

    葉片內部通道冷卻在航空發動機葉片的設計中佔有重要的位置，航空發動機進口溫度的增高對其提出了更高的要求。由於葉片內部通道冷卻的流動與傳熱的復雜性，數值模擬較實驗的研究方法有其優越性，本文利用數值模擬的方法對葉片內部通道冷卻進行了研究。
  8. Temperature field of hollow ingot solidification is simulated by fem. to different mould, effect of heat transfer coefficient between inner sleeve and cooling medium and thickness of core refractory on final position of solidification, the highest temperature of inner sleeve against cooling medium, and shrinkage cavity and porosity are compared. in addition, change of temperature in typical position of core refractory is also compared

    對空心鋼錠凝固過程的溫度場進行了有限元分析，對不同錠型結構的芯部換熱系數、耐火材料厚度對最終凝固位置、內筒壁最高溫度及縮孔疏鬆的影響進行了對比，並討論了耐火材料典型部位的溫度隨凝固時間的變化。
  9. Abstract : temperature field of hollow ingot solidification is simulated by fem. to different mould, effect of heat transfer coefficient between inner sleeve and cooling medium and thickness of core refractory on final position of solidification, the highest temperature of inner sleeve against cooling medium, and shrinkage cavity and porosity are compared. in addition, change of temperature in typical position of core refractory is also compared

    文摘:對空心鋼錠凝固過程的溫度場進行了有限元分析，對不同錠型結構的芯部換熱系數、耐火材料厚度對最終凝固位置、內筒壁最高溫度及縮孔疏鬆的影響進行了對比，並討論了耐火材料典型部位的溫度隨凝固時間的變化。
  10. The inner stress produced by quick cooling during quenching is the basic reason of formation of quench - distortion of parts

    摘要淬火過程中的快速冷卻在工件內部產生的內應力是導致淬火變形的根本原因。
  11. Double - deck stainless steel inner in heating section, and automatic radiator system fitting in sloww - cooling sect

    加熱段雙層不銹鋼內膽，緩冷段有自動散熱系統裝置。
  12. This paper briefly presents the theory of the inner evaporative cooling system with pump in generator and a suit of simulation software developed based on it using c computer language

    本文簡要介紹了汽輪發電機定子繞組內部蒸發冷卻的技術原理，著重介紹了一套基於此基礎之上的用c語言開發的模擬軟體。
  13. The outer surface temperature of barrel can be efficiently cooled down by adopting the outside cooling fluid method in a rapid - fire gun, but its effect on reducing barrel inner peak temperature and prolonging the life is limited

    （ 2 ）對于速射火炮，外液冷方式可以有效降低身管外壁的溫度，但對于身管內膛溫度的降低和壽命的提高作用有限。
  14. This type of air - cooling inner - furnace high - temperature monitor system has already been in uaed in shanghai bao steel and many power plants at home and abroad

    該種氣冷內窺式高溫工業電視系統已在寶鋼及多家火力發電廠投入使用。
  15. Numerical simulation to the influences of inner cooling apparatus on molten steel flow in billet mould

    板坯連鑄浸入式水口出口速度對結晶器流場影響的數值模擬
  16. Ferrari ' s brake cooling system has two main parts - an inner drum ( in yellow ) where cool air ( blue arrows ) enters, and an outer part where heat from the brakes ( red arrows ) is expelled

    法拉利的煞車冷卻系統包含兩個部份，一個讓冷空氣（藍色箭頭）進入的內部煞車鼓（黃色部份） ，外側部份則是用來排出煞車所產生的熱氣（紅色箭頭） 。
  17. Combined features of the inner impingement and outer film cooling holes of a vane

    內部沖擊和外部氣膜的組合特性研究
  18. According to the research results from som model, 8 sub neural network is adopted in inner and mae of hourly cooling load prediction is reduced 80. 64kwh. expected error percentage ( eep ) is reduced to 3. 27 %. next 24 hours hourly cooling load prediction multi - output dynamic model is established and prediction accuracy is improved again

    建立了一個統一的空調逐時負荷的24小時提前人工神經網路預測模型，並根據對日冷負荷類型的som分類結果，通過在內部一共採用8個子神經網路模型使得逐時負荷預測平均絕對誤差降低到了80 . 64kwh ，期望相對誤差降低到了3 . 27 。
  19. Turbine is of reactionary single shaft three cylinders with double exhausts subcritical pa - rameter and intermediate reheat, which is the product of abb switzerland. the generator is of static excitation and hydrogen inner cooling type of hydro - gen cooling core with water cooling stator

    汽輪發電機組為瑞士abb公司產品，亞臨界中間再熱三缸雙排汽單軸冷凝反動式汽輪機發電機採用靜態勵磁水氫氫冷卻方式。
  20. Technical features of chemical injecting system for inner cooling water of 660mw generators in hanfeng power plant

    發電機組內冷水系統加藥控制技術特點
分享友人
分享到 Line

分享到臉書