input amplifier 中文意思是什麼
input amplifier
解釋
輸入端放大器-
The system cybernation method is distributed control system. in this way, the audio process computer switch the signal between input and output channels. the main function of audio process computer is general broadcast, service broadcast and emergency broadcast. there is a special control computer. it " s main function is supervise - control the system status such as the amplifier and speaker circuit
在控制上，採用了分散式控制方式，由語音計算機進行音源輸入和輸出的切換，執行業務性廣播、服務性廣播和火災事故緊急廣播；由控制計算機進行系統的監控，監視功率放大器和揚聲器迴路的工作狀態，並根據當前的設備狀態執行相應的控制任務。 -
If the node is at, or near to, ground then a grounded guard ring will be appropriate, if it is at some other potential it may be necessary to use a high input impedance buffer amplifier, with its input connected to the node, to force the guard ring to the node potential
如果被保護的節點的電位是（或接近）零電位，採用地線保護環最為合適；如果節點電位是其他值，那麼可以用高輸入阻抗放大器組成緩沖器，輸入端連接該節點，輸出端連接保護環。 -
The power ’ s quality is decided in the system performance, the amplifier has 4 groups ’ power sources, input 220v through the filter, the transformer transformation, the full - wave rectification, finally through manostat leveling off voltage, after the electric capacity filter outputs
電源質量的好壞是決定系統性能的一個重要因素，放大器共4路電源，輸入220v通過型濾波，變壓器變壓，全波整流，最後通過三端穩壓器穩壓，電容濾波后輸出。 -
The input signals pass through the prepositive circuit which transforming the measured signals ( voltage or current ) into small voltage signals, the signal adjust circuit consist of programmable - gain amplifier and filter, and digital signal processor tms320lf2407 for data acquisition and processing in turns. provide the measuring results on lcd module. and also can transfer data to the pc ’ s rs232 for farther analyse
採用前置電路將被測信號（電壓或電流）變換為小電壓信號，經過信號調理電路對信號進行程式控制放大和濾波后，通過tms320lf2407實現信號的數據採集、信息處理和計算，將測量結果通過液晶模塊顯示，還可經過rs232介面與計算機進行數據傳輸，做進一步的分析和應用。 -
Test results show that under 2 - tone test in 5mhz tone spacing, the power amplifier system achieves - 50dbc imd3 with 20w output power, improved 20db in imd3 compared with the one without linearity. estimated value of aclr comes to 53db, which satisfies the 3gpp requirement for wcdma base - station transistor. further tests with alterative input power indicate a steady suppression to the imd3 controlled by the adaptive system
測試結果表明，自適應前饋功放系統在雙音輸出功率20w時三階交調系數小於- 50dbc ，鄰通道泄漏抑制比（ aclr ）的估算結果大於53db ，在理論上滿足3gpp對wcdma基站發射機的指標要求。 -
We apply the agrawal ' s theory model of soa, and study the temporal characteristics of the output pulse for input picosecond optical pulses with different sharpness edges passing through a semiconductor optical amplifier, and find that the peak power and the pulse width of the output pulse depend on the input pulse peak power, the sharpness degree of the input pulse edge and the bias current of soa
本文應用agrawal的關于soa理論模型，詳細研究了具有不同陡峭邊沿的皮秒超高斯光脈沖經soa后的時域特性的變化，發現輸出脈沖的峰值功率、脈沖寬度與輸入脈沖的峰值功率、輸入脈沖邊沿的陡峭程度以及soa的偏置電流密切相關。 -
A high efficiency dual - band rf power amplifier has an output and / or input of a high frequency transistor well terminated at the second harmonic frequency for dual - band operation
本發明乃一種高效率雙頻射頻功率放大器，提供高頻電晶體的輸出端與?或輸入端于雙頻操作中有良好的二階諧波終止。 -
In active section, in order to meet performance of out put power above 10dbm, the power amplifier module of ka - band is fabricated by using hmc283 to achieve the 14db conversion gain. there are five parts that include of waveguide - to - microstrip ? mixer ? filter ? power amplifier and waveguide - to - microstrip. input signal ' s power is 10dbm, after it pass waveguide - to - microstrip, it ' s frequency is escalate from 30ghz to 35ghz
該組件由五個部分組成：功率為10dbm信號經過波導? ?微帶過渡，然後混頻，濾波將30ghz提高到35ghz濾除不需要的諧波鏡頻以及三階交調信號，為了彌補混頻濾波的變頻損耗，加一級功率放大器，此放大器採用hittle公司hmc283晶元，此上變頻放大組件完成了上變頻?濾波?放大功能。 -
We have designed different measurement instruments according to the methods. the instrument used to measure electrode is a high precision multi - channel system constructed with a iaadc as the core and high input impedance amplifier and low input current multiplexer
對于硫屬玻璃電極，我們設計了以高精度的adc為核心，配以高輸入阻抗低噪聲的前置放大器和低漏電流多路模擬開關的多路精密電極測量系統。 -
An instrumentation amplifier is a closed - loop gain block that has a differential input and an output that is single - ended with respect to a reference teminal. it must amplify the differential input acurately and suppress any unwanted common - mode signals
儀表放大器是一種能精確放大兩輸入端之間的差模信號而抑制任何共模信號，並將差分輸入轉換為單端輸出的放大器。 -
This is a low impedance discrete level control which sits between the preamp active circuitry and the input to your power amplifier
這是一個位於前級有源電路和后級放大器輸入端之間的低阻抗的音量控制。 -
In order to obtain high resolution of the instrument, the effect of input noise of amplifier must be decreased. hereby, an amplifier circuit based on the chopping theory was developed for it
由於該微摩擦測試儀要求的分辨力很高，而運算放大器本身的輸入噪聲嚴重影響系統的解析度，為此設計完成了基於斬波放大原理的放大電路。 -
A resolution method in software is applied to calibrate zero point and full scale of the circuit. software approach to nonlinear correction for sensor and circuit is presented. therefore system error is eliminated, and measurement accuracy of temperature is improved. the signal of acidity electrode is detected by a differential amplifier circuit, which consists of operational amplifiers tlc2254 with high input impedance and low drift
採用橋路和單運放差動放大電路對溫度傳感器信號檢測放大，軟體校正溫度傳感器和測量電路的非線性，軟體校準測量電路的零點和滿度，消除測量電路的系統誤差，提高補償溫度的測量精度；採用高阻、低漂移運放tlc2254組成高阻差動放大電路用於酸度電極信號測量。 -
The ratio of output power from an amplifier system, to the input power. gain is normally measured in decibels
放大系統的輸出功率與輸入功率之比，增益通常用分貝表示。 -
2. the input stages of the ccii and the operational amplifier in transimpedance implifier are realized with folded cascode amplifier to reach high cmrr, large open loop gain and low offset
2 .為了提高儀表放大器的電源抑制比，並得到大的開環增益，相對低的失調等性能，電流傳輸器的輸入級和跨阻放大器中運算放大器輸入級均採用折疊共源共柵放大器。 -
In order to measure the characteristics of such semiconductor optical amplifier, we adopted a set of measurement system. this measurement system can be used to measure the characteristics of all kinds of active or inactive optical passive components. such device presents good polarization insensitivity ( < 0. 9db ), wide 3db bandwidth ( > 33nm ) at 0 - 200ma and different input signal light wavelength and power, the maximum fiber - to - fiber gain of 10db, lossless operation current of 50 - 75ma for different input signal light wavelength and power, large extinction ratio ( > 50db ) and lower noise figure ( nf ) ( < 8db )
與張瑞英博士一起，首次利用該種有源區結構制備出偏振不靈敏半導體光放大器，並在0 - 200ma注入電流范圍內獲得33nm的3db帶寬，在不同信號波長，不同信號功率0 - 200ma的注入電流范圍內，偏振相關損耗均《 0 . 9db ，在耦合差損為7db / facet的條件下，最大fiber - to - fiher增益達10db ，無損操作電流為50 - 70ma ，消光比達50db以上，而噪聲指數則低於8db ，最小可達4 . 6db 。 -
Analysis of input resistor of non - inverting operational amplifier
同相型運算放大器輸入電阻的分析 -
The thesis has done the widespread investigation and study to the domestic and foreign ’ s technologies of analogy low voltage and low power, and analyzes the principles of work, merts and shortcomings of these technologies, based on the absorption of these technologies, it designs a 1. 5v low power rail - to - rail cmos operational amplifier. when designing input stage, in order to enable the input common mode voltage range to achieve rail - to - rail, it does not use the traditional differential input pair, but use the nmos tube and the pmos tube parallel supplementary differential input pair to the structure, and uses the proportional current mirror technology to realize the constant transconductance of input stage. in the middle gain stage design, the current mirror load does not use the traditional standard cascode structure, but uses the low voltage, wide - swing casecode structure which is suitable to work in low voltage. when designing output stage, in order to enhance the efficiency, it uses the push - pull common source stage amplifier as the output stage, the output voltage swing basically reached rail - to - rail. the thesis changes the design of the traditional normal source based on the operational amplifier, uses the differential amplifier with current mirror load to design a normal current source. the normal current source provides the stable bias current and the bias voltage to the operational amplifier, so the stability of operational amplifier is guaranteed. the thesis uses the miller compensate technology with a adjusting zero resistance to compensate the operational amplifier
本論文對國內外的模擬低電壓低功耗技術做了廣泛的調查研究，分析了這些技術的工作原理和優缺點，在吸收這些技術成果基礎上設計了一個1 . 5v低功耗軌至軌cmos運算放大器。在設計輸入級時，為了使輸入共模電壓范圍達到軌至軌，不是採用傳統的差動輸入結構，而是採用了nmos管和pmos管並聯的互補差動輸入對結構，並採用成比例的電流鏡技術實現了輸入級跨導的恆定;在中間增益級設計中，電流鏡負載並不是採用傳統的標準共源共柵結構，而是採用了適合在低壓工作的低壓寬擺幅共源共柵結構;在輸出級設計時，為了提高效率，採用了推挽共源級放大器作為輸出級，輸出電壓擺幅基本上達到了軌至軌;本論文改變傳統基準源基於運放的設計，採用了帶電流鏡負載的差分放大器設計了一個基準電流源，給運放提供穩定的偏置電流和偏置電壓，保證了運放的穩定性;並採用了帶調零電阻的密勒補償技術對運放進行頻率補償。 -
The amplifier was being used as a unity gain buffer with an electrochemical cell and the non - inverting input was connected to a platinum electrode and to nothing else
該用戶的電路中，放大器用作緩沖器，其反相端除了與電池的一個白金電極相連之外，沒有其他電氣連接。 -
Abstract : by using the pulse - sequence model ， the inverse problem of amplification of broad - spectral - bandwidth laser pulse has been studied ， i. e. ， to find the initial input temporal pulse profile ， spatial profile ， spectral distribution and fluence from the required output temporal ， spatial pulse profile ， spectral distribution and fluence as well as the given amplifier parameters
文摘:採用脈沖分割模型，研究了寬頻帶激光脈沖放大的逆問題，即由所要求的輸出激光脈沖時間、空間波形、光譜分佈和能量密度，並給定放大器參數情況下，求輸入激光脈沖時間波形、空間、光譜分佈。
分享友人