integral controller 中文意思是什麼

integral controller 解釋
積分調節器
  • integral : adj 1 完全的；缺一不可的，主要的。2 【數學】整的，積分的。n 全體，整體；【數學】積分。 definite i...
  • controller : n 1 管理人，主管人。2 （會計的）主計人，檢查員；〈英國〉（特指宮廷、海軍等的）出納官〈常作 comptr...
  1. The controller includes two control loops which are outer speed loop ( variable parameter pi adjustment ) and inner current loop ( single - chop current delta - control ). in order to improve system performances, design of digital control system based on dsp is presented. the proportional parameter and integral parameter can be obtained through the design

    整個系統採用變pi參數轉速調節（外環）與單斬電流滯環調節（內環）相結合的雙閉環控制方式，為了得到既快速又穩定的恆速系統，本文還給出了基於dsp的雙凸極永磁電機數字控制系統的設計方案，通過此設計方案可以得到轉速環的比例參數kp和積分參數ki的參考值。
  2. Considering the big scope and nonlinear characteristic of tyre wheel model parameters, combination controller of fuzzy and integral is here applied, and its fuzzy control rule table and fuzzy control lookup table are listed

    針對機輪模型參數變化范圍較大，並且具有非線性的特點，研究了模糊積分混合控制器，給出了模糊控制規則表和模糊控制查詢表，並進行了模糊積分混合控制的模擬。
  3. Regarding the hysteretic properties and time - varying of the system, the scan round performance of the controller, adopt incremental pid algorithm in constant - pressure controlling and combine it with the integral - separated dead - zone algorithm as appropriate for the situation of the measuring system and applies fuzzy self - tuning to control pid controller parameters

    由於系統的滯后時變性和控制器的循環掃描工作方式，恆壓控制採用增量式pid控制演算法，結合測量系統實際情況加入積分分離帶死區改進演算法，並對pid參數進行模糊自整定控制，設計了一種參數自整定模糊pid控制器。
  4. This paper put forward a method of using amending sine value in the spwm sine table. this method can correct the distortion of the output voltage waveform, which resulted from the dead time used to the voltage type whole bridge main circuit. the inverter system adopts digital fuzzy controller with feed forward correction and which proportion coefficient and integral coefficient is changeable, so dynamic response is improved

    本文提出了一種採用修補spwm正弦表值的方法，用以改善電壓型全橋逆變主電路因上下橋的功率器件切換時先關斷后導通的死區時間而引起的輸出電壓波形畸變；逆變系統採用帶前饋校正的變比例變積分系數的模糊控制器，提高了系統的動態響應指標；系統設計了完善的保護措施，並具有市電電網的故障診斷功能。
  5. The design of force feedback loop is emphasized on the base of theory analysis. then proportional - integral controller and lag - lead compensator are designed to improve dynamic performance of this kind of gyro. the main work includes optimizing parameters and system simulation

    用matlab分析了陀螺本體傳遞函數的波德圖，然後通過採用比例-積分控制和遲后-超前校正及參數優化、系統模擬，使陀螺系統的固有頻率得到顯著提高。
  6. A comparative study and simulation of different control schemes, for the brushless motor variable - speed system, is presented. the simulation results show that, with the outer speed loop based on conventional proportional - integral controller, the dynamic performance of the system is not content, while with intelligence controller, the performance improves, and with variable - structure control with sliding mode, the system response influenced slightly by the vary of the system parameters

    本文還對無換向器電動機雙閉環調速系統的不同控制方式進行了模擬比較，結果表明：採用常規的pi轉速調節器，系統的動態性能不是很好；採用簡單的轉速環智能控制器，系統的動態性能能得到一定改善；採用轉速環滑模變結構控制器，系統的響應特性受系統參數變化的影響較小，具有優異的動態性能。
  7. By combining the parameter smooth projection algorithm and the integral - type lyapunov design technology with the sliding mode design technology with boundary layer, the performances for the system to avoid the parameter drift phenomena, the chattering phenomena, and the controller singularity problem were improved

    通過將參數光滑投影演算法，帶飽和層的滑模面設計技術以及積分型李雅普諾夫設計技術集成起來，使得演算法提高了系統在抑制參數漂移、抖振現象、控制器奇異等方面的能力。
  8. At the same tune, the paper analyses and discusses the control projects of the above parts. as for the hardware of the control system, on principle of reliability and considering the badly working condition of the vibratory roller, the paper chooses the special controller sp ecializing in the realm of construction machinery ' s control system in order to insure the reliability of the control system and simplify it. about the control quality of the system, the paper establishes the mathematical modes of the frequency modulation system and the amplitude modulation system, analyses the irrationality of the amplitude modulation project, puts forward to apply proportional - integral - differential controller ( pid controller ) to the traveling system and frequency modulation system

    作為控制系統的方案設計的基礎，本文首先對影響壓實效果的振動參數進行了分析；然後針對智能振動壓路機的功能要求，將控制系統分為壓實參數的自動和手動控制、行走控制、轉向和蟹行控制以及智能灑水控制等幾個部分，對各部分的控制方案進行了分析對比和論證；在控制系統硬體設計方面，以可靠性為原則，考慮到振動壓路機的惡劣工況，選擇了專用於工程機械控制領域的專用控制器，使系統的硬體設計得以可靠性保障和簡化；針對控制系統控製品質問題，建立了調頻和調幅系統的控制模型，對調幅系統的控制不合理性進行了分析，提出採用pid控制器對行走和調頻系統進行校正；在軟體設計方面，對各個控制部分進行了軟體編程流程圖設計。
  9. The shortages of traditional pid ( proportion integral differential ) controller are that the system ’ s overshoot is large, regulation time is long and parameter is hard to be real - time adjusted and the system is difficult to meet the real - time control

    在這種情況下，傳統的pid控制器存在超調量大，調節時間長，參數不易實時在線調整的缺點，難以滿足實時控制的要求。
  10. In the time - domain, based on the principle of random sampling of dso. two way ( " time amplifing in dual slope integral " and " time - voltage convert " ) are implemented to measure the time between the system triger and writing clock. thus random sampling interpolate can be done to measure repeated signal in high frequency with the a / d convert and controller which frequency are lower

    在時域，根據數字示波器隨機取樣原理，用兩種方法（雙斜率積分時間放大測量方法和時間? ?電壓轉換測量方法）測量數字示波器系統觸發和采樣寫時鐘間時間間隔，用低速a / d轉換器及控制器進行模?數轉換和控制，以此進行隨機取樣內插，從而實現了對高頻率重復信號的測量。
  11. Too early switch can not present the advantage of fuzzy controller and even lead to integral saturation, while too late switch can not turn into pid control because of the static state error of fuzzy - ped control. at last, the choice principle of the threshold is analyzed and simulated

    當過早地切換會體現不出模糊控制的優點而使超調量增大，甚至造成積分飽和現象使系統失穩；當過遲切換，如果模糊控制器有較大的靜差，則有可能根本無法進入pid控制。
  12. In this paper, to resolve the coupling phenomena between temperature and humidity in wood drying system, a bp neural network based pid controller is proposed and applied to wood drying system. the architecture and learning algorithm of the proposed controller is more simpler and the physical meanings of the input layer ' s neurons and output layer ' s neurons are explicit. based on predefined control rules and self - learning, the bp network changs the scaling integral and differential parameters, therefore is able to control the variants using classical pid control algorithms and at the same time, decoupling control is implemented as well during the control procedure

    本文針對木材幹燥過程中溫、濕度耦合的現象，提出一種將新的基於bp神經網路的pid控制器應用於木材幹燥控制系統的方案，其結構和學習演算法相對簡單，輸入層和輸出層神經元物理意義明確；它根據設定的某一控制規律，通過網路的自學習，調整pid控制器的比例、積分和微分參數，從而利用經典的pid控制演算法得到相應各變量的控制量參與控制，並在該過程中實現解耦控制，而不用給定樣本信號進行在線的學習。
  13. A new method to design stable scaling universe of discourse of integral fuzzy controller based on center of membership function

    帶積分環節的隸屬度函數中心自適應模糊控制器設計
  14. Based on improvement of standard fuzzy controller, an integrated intelligent algorithm combining fuzzy logic with integral function and adaptive parameters is presented. the simulation results show it has better performance than conventional pid controller

    論文在標準模糊控制器基礎上，採用加積分環節的模糊控制演算法，自適應模糊控制演算法，模擬運行的結果表明其控制效果要優于pid控制。
  15. Via starting and stopping air compressor, it can make the ice of evaporator melt. this controlling system can display the temperature of railway carriage, control temperature with multi - grade setting and modify controlling parameters on line. the algorithm of fuzzy controller is revising factor ( a ) consulted on line fuzzy control with integral link

    模糊控制演算法採用帶有積分環節的修正因子在線插值的模糊控制，控制系統的輸入為車廂溫度與設定值的偏差和偏差的變化率，輸出為與溫度門開口角度相關的占空比可調的脈沖的占空比參數，均採用正態模糊數模型。
  16. Through simulation and calculating the four models, the influence on proportion coefficient, integral time constant, derivative time constant and partial feedback coefficient for system performance is analyzed. the ideal reference value of every parameters and step respond curves are given. the simulation result may be used as reference for making analogue controller or digital controller

    通過對這四種模型的模擬研究，分析了各模型中比例系數、積分時間常數，微分時間常數及局部反饋系數對系統性能的影響，並給出了各參數較為理想的參考值及階躍響應曲線，模擬結果對製作模擬控制器及數字控制器有一定的借鑒作用。
  17. 2. based on the original bp network, some improvement on error back propagation arithmetic is made. the executing speed of the algorithm is increased through online adjustment of learning rate. combined with traditional pid control, this method generated two integral schemes : bp network + pid serial control and self - confirming control of parameters of pid controller based on bp network are constructed

    在原有的誤差反向傳播（ bp ）網路的基礎上，對其學習演算法進行了改進，通過在線調節學習速率，提高了演算法的實現速度，並且與傳統的比例積分微分（ pid ）控制方法進行結合，分別實現了兩種集成方法： bp網路與pid串列控制方法和基於bp網路的pid參數自整定控制方法。
  18. Direct torque control using space vector modulation ( svm - dtc ) scheme is discussed and the detailed designed, including space vector choosing and modulating, to overcome the control difficulties coming with the characteristic of low inductance. comparing with the basic dtc, the simulation results confirm the feasibility and good performance of this strategy. in order to reduce the torque error in dynamic state resulted from the nonlinear relationship between the torque and torque angle, a proportional - plus - integral ( pi ) torque controller with variable proportion is presented to ensure exact and quick control of torque in dynamic state

    系統的闡述了永磁同步電機直接轉矩控制理論，分析了改進后的svm - dtc控制策略，並具體設計了控制技術的實現方案，包括參考矢量的生成和空間電壓矢量調制的方法；為減小電磁轉矩與轉矩角非線性關系這一因數給電機電磁轉矩動態調節造成的誤差，本文實現了變比例系數轉矩pi調節器的方案，確保了系統穩定性的同時，實現了電磁轉矩在動態過程中快速而準確調節。
  19. To multi - model plants, the fuzzy integral compound control method with a self - tuning parameter is proposed. the control simulation tests of the hydraulic turbine generator are made and the results show that the proposed controller has strong robustness and satisfied performances. 4

    針對具有多模型特性的受控對象，提出了一種參數自調整模糊積分復合控制方法，並以水輪機組的頻率跟蹤控制問題為背景，進行了控制系統的設計和模擬實驗研究，模擬結果表明這種新穎的控制方法具有強的魯棒性和滿意的控製品質； 4
  20. Proportional plus integral controller ; pi controller

    比例積分控制器
分享友人
分享到 Line

分享到臉書