interfacial shear strength 中文意思是什麼

interfacial shear strength 解釋
分界面抗剪強度
  • interfacial : adj. 1. 界面的，面際的。2. 界面角的。
  • shear : vt vi （sheared 〈古語〉 shore; shorn sheared）1 剪（羊毛等）；修剪（樹木）；剪（呢絨的）長毛。2 ...
  • strength : n. 1. 力，力量，體力。2. 強度，濃度；長處；（要塞等的）抵抗力。3. 實力；兵力；全體人數，額定人數，編制。4. 筆力；文勢。5. （證券等的）市價堅挺。6. 〈美俚〉（可能有的）利潤。
  1. In addition, a new analytical method was used to solve the shear strength of the fiber / epoxy interface. the result showed good agreement with that from the kelly - tyson equation. meanwhile, according to the sfc tests of the single fiber reinforced epoxy matrix composites treated by four types of surface treatments, the interfacial adhesion conditions were estimated by critical fiber length, interfacial shear strength and single fiber microdamge mode

    此外，文中對單纖維復合材料斷裂實驗運用了新的解析方法，求解了玻璃纖維環氧復合材料界面的剪切強度，與kelly - tyson等式方法求得的界面剪切強度有著很好的一致性；同時，對四種不同表面處理劑處理的單纖維復合材料斷裂實驗進行了分析，從臨界纖維長度、界面剪切強度和單纖維斷裂實驗中纖維斷點周圍基體形貌評價了界面的粘結情況。
  2. Through the experiment of the interfacial bonding shear strength and the shrinkage strain of concrete, the influence of the interfacial roughness of used concrete surface and interfacial bonding agent to interfacial bonding strength is revealed ; new concrete component and the shape and size of concrete slab are main factor affecting the shearing stress in layers

    試驗結果表明：老混凝土粘結面的粗糙度和界面粘結劑類型對新老混凝土界面粘結強度影響很大；新鋪混凝土材料和混凝土路面板形狀尺寸是影響新老混凝土粘結面收縮剪應力的主要因素。
  3. The results show that the interfacial shear strength increases after plasma treatment and reaches a maximum value, 16. 22 % greater than that before the treatment, when the filament is treated for 6 minutes

    處理9分鐘后，界面剪切強度比處理6分鐘時有所下降，但仍比未處理前有所增加。處理12分鐘后，界面剪切強度與處理6分鐘的試樣相比下降較多。
  4. At the same time, the energy absorbed in the crack propagation phase decreases relatively that lead to overall energy absorption of the composites increases slightly, it is greater than 12. 89 %. by observing the appearance of the damage area, it can be found that the mode of damage is influenced by the interfacial shear strength. if the interfacial shear strength is low, fiber pull - out is the primary energy - absorbing mechanisms, whereas the dominant energy - absorbing mechanisms changes into fiber / matrix debonding and delamination when the interfacial shear strength is stronger

    界面剪切強度增加后，材料的沖擊極限載荷有所增加，在裂紋起始區吸收的引發能增加較多，其中增強纖維經等離子體處理6分鐘的試樣所吸收的引發能增加了18 . 57 % ;由於裂紋擴展階段所吸收的能量相對有所下降，材料總的能量吸收能力雖有所改善，但增加不多，其中界面剪切強度增加最多的試樣，吸收的總能量增加了12 . 89 % 。
  5. Moreover, when the filaments are treated for 12 minutes, the interfacial shear stress will be lower than that treated for 6 minutes. izod pendulum is used to test the influence of the fiber / matrix bond strength on the low velocity impact responses of the composites. the curves of energy - time, force - time and velocity - time are obtained by a data acquisition system

    用擺錘低速沖擊儀對界面粘結強度不同的材料進行沖擊試驗，藉助數據採集系統得到沖擊過程中材料吸收的總能量、承受載荷、擺錘速度等參數與時間的關系曲線，並通過pc機處理，將載荷?時間曲線轉化為載荷?位移曲線。
分享友人
分享到 Line

分享到臉書