involute worm 中文意思是什麼

involute worm 解釋
漸開線蝸桿
  • involute : adj. 1. 紛亂的，錯綜復雜的。2. 【植物；植物學】內卷的。3. 內旋的；螺狀的。n. 【數學】漸伸線，漸開線，切展線。vi. 1. 內卷，捲起。2. 恢復原狀。3. 消失，消散。
  • worm : WORM ＝ Write Once Read Multiple 【計算機】一寫多讀光盤。n 1 蠕蟲；蟲，蛆；〈pl 〉（小孩等的）腸...
  1. Analysis of the axial profile of an involute helicoid worm

    漸開線圓柱蝸桿軸向齒形分析
  2. On the basis of the engage efficiency and lubricious conditions, theoretical transmission efficiency with the different drive ratios ( 1 / 50 and 6 / 31 ) of involute cylinder worm gears is analyzed. at the same time, the change trend of engage efficiency and transmission efficiency with different design parameters is discussed. the experimental investigation on transmission efficiency

    從漸開線蝸輪蝸桿傳動的嚙合效率和潤滑條件兩個方面對不同傳動比的漸開線圓柱蝸桿的傳動效率進行理論分析，並通過傳動比分別為1 / 50和6 / 31的漸開線圓柱蝸桿設計參數得到蝸桿潤滑條件的理論分析結果和蝸桿嚙合效率、傳動效率的變化趨勢，同時利用電測法對蝸桿傳動的傳動效率、潤滑油平衡溫度進行測試，將測試數據與理論計算結果進行對比分析，得出理論分析結果的正確性。
  3. Solid model of the involute worm gearing solid model with drive ratio 1 / 50 is built by using ideas - 5. 0, then the elastic contact analysis is proceeded on the basis of contact fem. the dynamic evolution image of the area of the contact zone, the load sharing among instantaneous meshing tooth pairs, the distribution of the contact force, and tooth stress are obtained. 3

    通過漸開線圓柱蝸桿、蝸輪的齒面方程式，利用ideas - 5 . 0軟體建立了傳動比為1 / 50的漸開線圓柱蝸桿傳動的實體幾何模型，在此基礎上應用接觸有限元方法對該傳動進行了彈性接觸分析，包括接觸區的形狀、位置、載荷在瞬時嚙合齒對的分配狀況； 3
  4. Tooth surface equations and contact line equations of the involute worm gearing are established according to its machining methodology. meshing characteristics in rigidity condition are studied. these characters include the inductive normal curvature along the contact line on the worm surface, the first and the second limit lines during the engage of the worm gear, and the influence of the intersect angle between the contact line the relative velocity of the worm and the gear on transmission performance

    根據漸開線圓柱蝸桿傳動的創成方法，建立了漸開線圓柱蝸桿和蝸輪的接觸線方程式、齒面方程式，分析了漸開線圓柱蝸桿傳動的剛性嚙合特性，如蝸桿與蝸輪嚙合時的誘導法曲率、一類界限曲線、二類界限曲線和蝸桿與蝸輪間相對速度方向和接觸線方向的夾角對傳動性能的影響； 2
  5. The process has an advanced principle. the involute hourglass worm drive can realize the design machining of gear form and direction, and the internal meshing honing gear has high efficiency. this process has all merits mentioned above, and also has the advantages of quality stability, high productivity for rude and finish machining

    該工藝原理先進，它集有利於實現齒形、齒向設計加工的漸開面環面蝸桿傳動與高效的內嚙合珩齒的優點與一體，對齒輪的粗、精加工都有質量穩定、生產效率高的優點。
  6. Grinding gear with the toroidal involute interior thread worm grind wheel is a new kind of process in hard surface gear finish machining

    漸開麵包絡環面內螺紋蝸桿砂輪磨齒，是一種硬齒面齒輪精加工的新型工藝。
  7. The software uses two entity configuration methods : extruding and simulating entity cutting in realizing three dimensional configuration, which successfully achieve three dimensional configuration of involute columnar vertical gear, involute columnar helical gear, standard vertical spline, archimedes worm and disco - cam

    軟體在三維造型功能實現上使用了拉伸和模擬實體切削兩種實體造型方法，成功地實現了漸開線圓柱直齒輪、漸開線圓柱斜齒輪、標準直齒條、阿基米德蝸桿和盤形凸輪的三維造型。
  8. Based on the method of least squarest the datasheets and charts which were used in designing involute worm gearing were formulated, then designed the predigested computer aided design program

    摘要運用最小二乘法對漸開線蝸桿傳動設計計算的有關數表和線圖進行了公式化處理，進而研製了這種傳動的簡化計算機輔助設計程序。
  9. The involute cylinder worm gear is one of the ordinary cylinder worm gears. because of the specificity of the machine tool for this worm gear, its machine tool is not extensively developed in our country. the deep research on the involute worm gear is lack in our country

    漸開線圓柱蝸桿是普通圓柱蝸桿中的其中一種，但由於加工這種蝸桿的機床的專用性太強，我國沒有廣泛發展這種機床，因此我國對漸開線蝸桿的研究還不夠深入。
  10. The central content of this thesis is theoretic and experimental analysis on involute cylinder worm gear under the coupling of the load and the mounting errors

    本文的中心內容是漸開線圓柱蝸桿承載嚙合理論與實驗分析。為此，論文在以下幾個方面開展研究。
分享友人
分享到 Line

分享到臉書