izod impact strength 中文意思是什麼

izod impact strength 解釋
艾佐德沖擊強度
  • izod : 伊佐德
  • impact : n 碰撞；沖擊（力）；（火箭的）降落[著陸]；【軍事】彈著；影響，效力。 The point of impact彈著點。 ...
  • strength : n. 1. 力，力量，體力。2. 強度，濃度；長處；（要塞等的）抵抗力。3. 實力；兵力；全體人數，額定人數，編制。4. 筆力；文勢。5. （證券等的）市價堅挺。6. 〈美俚〉（可能有的）利潤。
  1. The mechanical tests result showed that when the mmt content is 2 % and the compatilizer content is 15 %, the pmc has best mechanical property. the izod impact strength is 16. 45 kj / m2 and the tensile strength is 35. 77 mpa, increasing 280 % and 4. 3 %, compared with pure pp. the pom photo indicated that the o - mmt can reduce the scale of spherical crystal of pp

    以am為插層劑得到的聚丙烯蒙脫土納米復合材料中，蒙脫土保持剝離狀態，但力學性能不理想，當土含量為0 . 5時，材料的沖擊強度為9 . 58kj m ~ 2 ，拉伸強度為25 . 5mpa 。
  2. Based on the results of particle size analysis and sem observation as well as microstructural characterization of pp / fe co - powders, a pulverizing mechanism is proposed. the mechanical properties of pp / fe composites indicate that izod impact strength increased from 2. 86 kj / m2 to 4. 52kj / m2, 68. 7 % higher after 25 cycles of milling

    Bet比表面積、粒度分佈和sem分析表明， pp wtr共碾磨初期主要發生顆粒破裂細化，粉碎作用為主；碾磨後期，碾磨主要起混合作用，碾磨導致復合粉體比表面積下降，碾磨20次后比表面積下降為0
  3. If more psmn was added, izod impact strength of ppmn began to decrease

    繼續增加psmn的填充量，缺口沖擊強度開始下降。
  4. When the contents of other blending components were fixed, with the content increasing of psmn, izod impact strength of ppmn was enhanced gradually. when the content of montmorillonite was 2wt %, max value of 36. 24kj / m2 was achieved

    在其它共混組分含量不變的條件下，隨psmn填充量的增加，復合材料缺口沖擊強度逐漸提高，在蒙脫土填充量為2wt時達到最大值36 . 24kj m ~ 2 。
  5. The izod impact strength was increased 48 % and the tensile strength was increased 12 % contrast with pure pp, achieved the highest value when 3 % nano - sio2 by weight modified with silicone coupling agent and pp - g - mah was added

    加入3納米sio _ 2粒子，復合增容劑5份時復合材料力學性能最佳，相比純pp其沖擊強度提高48 、拉伸強度增加12 。
  6. Plastics - determination of izod impact strength

    塑料.懸臂梁式沖擊強度的測定
  7. Izod plastics - determination of izod impact strength

    塑料製品.埃左氏
  8. Testing method for izod impact strength of glass fiber reinforced plastics

    玻璃纖維增強塑料的埃左氏沖擊強度的測試方法
  9. Moreover, when the filaments are treated for 12 minutes, the interfacial shear stress will be lower than that treated for 6 minutes. izod pendulum is used to test the influence of the fiber / matrix bond strength on the low velocity impact responses of the composites. the curves of energy - time, force - time and velocity - time are obtained by a data acquisition system

    用擺錘低速沖擊儀對界面粘結強度不同的材料進行沖擊試驗，藉助數據採集系統得到沖擊過程中材料吸收的總能量、承受載荷、擺錘速度等參數與時間的關系曲線，並通過pc機處理，將載荷?時間曲線轉化為載荷?位移曲線。
分享友人
分享到 Line

分享到臉書