joint surface 中文意思是什麼
joint surface
解釋
關節面-
Copper has been deposited on surface of the al mmcs as interlayer by magnetron sputtering, tlp bonding of al mmcs with these interlays, the joints shear strength of tlp bonding using deposited film was as much as the joint shear strength of tlp bonding using cu foil. removing the oxidation on the surface before deposition, copper was coated by magnetron sputtering as tlp bonding interlayer
待連接表面通過磁控濺射法沉積銅膜作為中間層進行瞬間液相連接，得到的接頭強度與銅箔中間層進行瞬間液相連接得到的接頭強度相當，而使用磁控濺射法去除待連接表面氧化膜后沉積銅膜作為中間層進行瞬間液相連接的接頭強度提高7 . 6左右。 -
The following definitions apply to any planar surface, e. g. bedding, fault, joint or cleavage planes, veins or mineral deposits.
以下諸定義適用於任何平面，如層面，斷層面，節理面或劈理面，巖脈或礦床。 -
When tlp bonding with proper pressure, the oxidation on the surface of al mmcs was n ' t the primary effect of the properties of the joint
採用適當的壓力進行瞬間液相連接時，鋁基復合材料表面的氧化膜已不是影響接頭性能的主要因素。 -
Boasted joint surface
寬鑿接縫槽面 -
The link should be formed steel plate, plate edge, no burr hole ; a joint warping, used to be calibrated to prevent injury and friction, the friction surface to ensure close
連接處的鋼板或型鋼應平整，板邊、孔邊無毛刺；接頭處有翹曲、變形必須進行校正，並防止損傷摩擦面，保證摩擦面緊貼。 -
Solder bar is made from high purity metal. by means of strict qualitg control the oxide and metallic and non - metallic impnrities and effectively minimized, the available high purity solder bar is with uniform and glazed surface good wetting and spreading ability after molten bright joint and minimum oxide residue after soldering. our product is suitable for wave and handwork soldering with high quality requirement
本公司生產焊錫條採用高純度金屬原料，在嚴格品管條件下，有效控制氧化程度以及金屬和非金屬雜質含量，焊錫條表面均勻光滑，純度極高，熔化后流動性好，潤濕性極佳，焊點光亮，氧化渣物極少發生，適用於高品質要求的各種波峰焊和手工焊。 -
At last, the surface of the alumina femoral head was grade - polished with sic micropowder and diamond grinding cream, the join part was trimmed with specific instrument, which made the surface of the alumina femoral head reach the degree of approximating mirror finish and match the femoral stem well. the artificial partial hip joint prostheses was finally got by articulating the alumina femoral head with ti alloy femoral stem coated with bioactive coating
最後，採用sic超細粉和金剛石研磨膏對氧化鋁陶瓷股骨頭表面進行分級拋光，用專用器械修整其聯接部位，得到表面具有近似鏡面光潔度並與股骨柄配合良好的氧化鋁陶瓷股骨頭，並與表面塗覆生物活性塗層的鈦合金股骨柄配伍，最終獲得人工半髖關節假體。 -
Construct a three dimensional space finite element analysis model for the steel mix joint part of road bridge surface, study the distribution complexion of strain field in the steel combine part, and judge its endurance and safety capabilities
對公路橋面板鋼混結合部位，建立三維空間有限元分析模型，研究鋼混結合部位的應力場的分佈情況，評判該部位的受力性能及安全性能。 -
Lastly, two conditions were simulated and computed by using the fem program : two pieces of joint and one piece of joint which have different depth, different grouting stress, different pressure on the ground surface, etc. and then some results were obtained about the relation of the grouting press, the lifting of the ground surface and the cosumptionof the injection grout
最後，依據所編的程序對不同埋深、不同灌漿壓力、不同壓重等的單條節理裂隙的灌漿情況和兩條節理裂隙的灌漿情況進行了模擬計算，得出了一些結論：灌漿壓力、地表抬動和注漿量之間的關系。 -
A method to identify the damping parameters of machine joint surface is proposed based on the tested frequency response functions
提出一種基於實測傳遞函數矩陣來識別機械結合面阻尼參數的新方法。 -
Aim at the influence that different material of the adhesive boned joint and the different surface processing method connect the strength, we chose the surface processing method that spray sand to remove the rust add wreath oxygen to prepare draw the paint when construction operation
針對膠接接頭的不同材質及不同表面處理方式對膠接強度的影響，我們通過分析選擇了在膠接時應用噴砂除銹+環氧預塗的表面處理方式。 -
Among them, operating with the power from the tip of the thumb is called finger - tip pushing ; in which the interphalangeal joint of the thumb is fixed at the back - stretching position, operating with the force from the whorled surface is shao - shang point at the side of the thumb - radius is called lateral pushing, in this operation, the operator slightly flexes his wrist joint with index finger, middle finfer, ring finger and little finger naturally stretching forward in the finger - separating pattern
以拇指端峰為著力點操作的稱指峰推；操作時，拇指之間關節固定在背伸位，以羅紋面為著力點的稱羅紋推；以拇指橈側少商處為著力面的又叫偏峰推，此法操作時腕關節略屈，食、中、無名、小指向前自然伸開，成散手狀。 -
Objective to report the result of the defects of metacarpophalangeal joint from 2 to 5 repaired by metacarpal articular surface with dorsal metacarpal artery and using kirschner pins to transfix the injured finger and the nearby normal finger
目的報道利用傷指鄰近的正常手指作為生理性外固定支架與傷指並指固定，應用帶血供的掌骨近端骨塊修復2 - 5掌指關節缺損的效果。 -
In chapter two, the prosperity of the motion, force and screwed joint of the surface dynamic rotating drilling downhole drilling string has been discussed
第二章分析探討了地面動力旋轉鉆井井下鉆柱的運動狀態、受力及螺紋聯接的特性。 -
Considering the joint operation of the three gorges and gezhouba hydropower stations, influences of the daily regulation planning of the hydropower stations on the water surface slope of the downstream reach of the three gorges reservoir are studied
?結合三峽和葛洲壩兩電站聯合運行的實際情況，研究了調節方案對三峽水庫下遊河道水面比降的影響。 -
This paper researches the influence of no treating, paving cement and fly ash paste, and paving cement mortar on rcc layer surface upon the ultimate tensile strain of placing joint of rcc layers under the condition of different interval of placement of rcc layers and different amount of binding materials
研究在不同的層間間隔時間條件下，採用不同的膠凝材料用量，對碾壓混凝土層面分別採取不處理，鋪水泥粉煤灰漿（簡稱水泥凈漿） 、水泥砂漿等處理措施對碾壓混凝土層面極限拉伸值的影響。 -
Remove paint, sealing layer ( protection layer ), resin emulsion cement ( wear - resisting flooring ), protruding part, rain trace, trowel mark, rough surface, uneven joint etc
去除油漆、密封層（保護層） 、膠脂水泥（耐磨地坪） 、高出部分、雨跡、鏝刀痕、粗糙表面、不平接縫等。 -
The joint surface normal stress is worked out and then the minimum sleeve press - in force, by which tightening bolt number is determined, ensuring that the sleeve is fastened and the desired torque is delivered
根據結合面的壓強計算了壓入襯套所需的最小壓入力，並依此確定緊固螺釘的數量，以確保壓牢襯套，滿足傳遞扭矩的需要。 -
The method of surfacing welding sealing strip was adopted to repair the deformation of the flange joint surface of the high and intermediate pressure outer casing
摘要湛江發電廠在1999年1 （上標# ）機組大修中採用堆焊密封帶方法修理了汽輪機高中壓外缸中分面的變形缺陷。 -
The model can reflect the multi - sets feature of the rock masses in practice, consider the influence of the joint orientation and strength to the rock masses deformation feature, and simulate the simultaneous sliding, tension and close behaviors of the multi - sets jointed rock masses extending the joint surface, and reflect the plastic deformation induced the rotation of the principle stress axes. the result can be extended to fractured rock masses with arbitrary set joints
該模型能反映實際工程中巖體的成組節理特性，考慮節理產狀和強度對巖體變形特性的影響，可用來模擬巖體中多組節理同時存在滑動、張開、閉合的行為，並能反應由於應力主軸旋轉所產生的塑性變形的影響。
分享友人