junction test 中文意思是什麼
junction test
解釋
連接試驗-
Standard test method of measurement of common - emitter d - c current gain of junction transistors
結型晶體管共射極直流增益測量的標準試驗方法 -
We introduce the fabrication of all samples and anneal of fexcu ( 1 - x ) granular film in detail. the configuration of granule film is investigated by scanning tunneling microscope ( stm ). the matter phase is analyzed by x - ray diffraction ( xrd ). the hysteresis loop of co / al2o3 / feni magnetic tunnel junction is studied by vibrating sample magnetometer ( vsm ). we use microresistance test system ( mts ) to investigate the character of resistance, conductance, voltage and current
用掃描電子顯微鏡（ stm ）觀察顆粒膜樣品的表面形貌；用x ?射線衍射儀（ xrd ）對顆粒膜樣品進行物相分析；用振動樣品磁強計（ vsm ）對co al _ 2o _ 3 feni隧道結的磁滯回線作了研究；用微電阻測試系統對樣品電阻、電導、電流、電壓相關特性進行詳細的研究。 -
Another test method for junction depth
測試結深的另一種方法 -
Hydraulic pressure test of long distance pressure water conveyance culvery junction
長距離有壓輸水箱涵接頭水壓試驗 -
The test junction is usually embedded in the material whose temperature is to be measured.
測試結通常埋在待測溫度的物質中。 -
In practical application, the m10 180 bolts, which are installed in the head cover of the torque divider of ts5560 special automobile, sometimes fracture all of a sudden. according to the tests of acceleration, stress and strain, and the exciting test, it is resonance vibration that leads to the compound - bending fatigue fracture of the bolts. the exciting force caused by drive system, transmitted through the torque divider, produces a 1000 - 1500hz cyclical excitation at the junction of the bolts and head cover, which causes the first order bending resonance vibration of the bolts
通過加速度、應力應變測試實驗和激振試驗的研究，發現ts5560特種車分動器取力器氣缸端蓋m10 180螺栓斷裂問題是由於共振引起的雙向彎曲疲勞斷裂：傳動系統工作所產生的激勵，經過分動器結構的傳遞（特別是分動器一階扭轉模態的放大） ，在螺栓的連接處產生1000 1500hz的振動激勵，其導致螺栓一階彎曲共振，在螺栓一階彎曲模態的阻尼比較小的情況下，使得螺栓產生較大的共振響應，導致螺紋處的彎曲動應力較大，疲勞壽命較低。 -
To increase the accuracy of the test method, a steady - state operation life test method with additional measuring and strictly controlling transistor junction temperature, in the highest temperature range, is given
旨在提高晶體管穩態工作壽命試驗方法的可信度，提出了一種在試驗過程中實時測量並嚴格控制晶體管結溫在最高允許結溫附近的穩態工作壽命試驗方法。 -
Analyzing the various problems of current steady - state operation life test standard, it is pointed out that, not measuring and controlling, transistor junction temperature in current transistor steady - state operation life test can lead to fatal inaccuracy of the test results
摘要在分析了現行標準中晶體管穩態工作壽命試驗方法存在問題的基礎上，認為在現行的穩態工作壽命試驗中沒有對晶體管的結溫實施測量和控制，是導致試驗結果不準確的重要原因。 -
Pias1, a protein that was also located in test ' s specifically was got pdz domain protein tight junction protein 2 and pcg ( polycomb group ) family ring1 and polycomb 2 were included
3kbp （ kyotbindingpotcin ）功能的研究： kbp是我們通過酵母雙雜交獲得的與kyo 』 fz相互作用的一種新分子。 -
Based on the test result of hydraulic model of a project, this paper analyzes the influences of gate operation during operating period, combined operation of hydro - generation sets and the length of guide wall on navigable flow condition in entrance area, and proposes the operation mode of the hydro - junction for improving navigation flow condition
摘要根據實際工程的水工模型試驗資料，分析樞紐工程運行期的閘門調度、機組組合運行和導航墻長度對口門區通航水流的影響，提出改善通航水流條件的樞紐運行方式。
分享友人