kinemics 中文意思是什麼

Thirdly, a feasible method to solve the inverse - kinemics problem based on cmac isrealized and validated by simulation results under matlab

然後，實現了一種可行的基於cmac的逆運動學求解方法，並通過matlab模擬對該方法進行了驗證。

In this dissertation, both single and complex driver - magnifier as a whole body is tested and studied by the tool of ansys for the deep analysis of kinemics, workspace, error analysis and compensation. and the method of helix - mechanism is induced to study the model accurately

本文利用ansys工具對智能並聯微執行器驅動機構的柔性鉸鏈進行了分析與模擬，為並聯微操作機器人整體性能測試及分析，即微執行器的位置空間、運動學、誤差補償提供了基礎。

In chapter 2, author points out firstly that the elastic deformation of elastic units of a robot ' s wrist force sensor will be enlarged by the end - effector, the instruments and the work pieces, so the elastic deformation of the sensor will influence the location accuracy or kinetic accuracy of end point of a robot, under the condition of that the robot technology facing the developing of heavy load, light mass and high accuracy. it is discussed respectively that the relationship between the differential kinemics in the sensor ' s coordinate and the location accuracy or kinetic accuracy of the end point. error matrixes of location and kinemics of the end point are presented respectively based on the differential kinemics in the sensor ' s coordinate, and the on - line error compensation methods are introduced subsequently

第二章首先指出機器人腕力傳感器彈性體的彈性變形經過機器人末端連桿、工具、工件等的放大后，會對機器人末端精確定位和運動產生的影響；然後分別研究了傳感器坐標系內的微分運動與機器人末端工件精確定位、運動的關系；在此基礎上，研究了基於腕力傳感器彈性體微分運動的機器人末端定位、運動誤差的誤差矩陣及其在線誤差補償方法；基於機器人動力學的機器人末端定位、運動誤差的誤差矩陣及其在線誤差補償方法；最後，以puma型機器人為對象，給出了基於腕力傳感器內微分運動的機器人末端定位、運動誤差及其在線補償方法的模擬實例：給出了基於機器人動力學的機器人末端定位、運動誤差及其在線補償方法的模擬實例；模擬結果表明， 1 ）基於腕力傳感器的機器人末端定位誤差在腕力傳感器允許的載荷下可達十分之幾毫米級。

And then, the error matrixes of location and kinemics of the end point, and the on - line error compensation method are given based on robot ' s dynamics. finally based on puma robot, three simulation examples are given respectively ; the first is about the location error and on - line location error compensation, the second is about the kinetic error and on - line kinetic error compensation, the third is about location and kinetic errors causing by robot ' s dynamics and the on - line error compensations. the simulation results show that : a ) location error of the end point based on elastic deformation of the sensor will be about millimeter ' s degree under the permitting load, b ) the on - line error compensation methods given are available

第三章首先概括了目前機器人連桿慣性參數識別的四種方法，總結這些方法的優、缺點；指出這些方法存在的問題是：或者需將機器人解體，不能在線進行參數識別，或者不能給出機器人連桿獨立的慣性參數值，只能獲得慣性參數的組合值，而這些方法的共同問題是：不能考慮機器人連桿的關節特性；本章提出了一種基於腕力傳感器的機器人末端連桿慣性參數在線識別方法，給出了該方法的理論計算和推導；研究提出了以腕力傳感器輸出為前提的、基於newton - euler動力學的機器人動力學正向、逆向遞推公式；針對機器人負載參數辨識必須在線、實時的特點提出了基於腕力傳感器的負載參數在線識別方法，給出了負載參數識別的步驟。