laminate thickness 中文意思是什麼

laminate thickness 解釋
材料厚度
  • laminate : vt 1 把（金屬等）輾壓成薄板。2 把…切[分]成薄片。 3 用薄片疊成。4 用薄板覆蓋。5 黏合（薄片）。vi ...
  • thickness : n 1 厚；粗；厚度；粗大。2 濃度，濃厚，黏稠。3 密度；稠密。4 模糊不清，多煙霧，混濁。5 愚笨；遲鈍...
  1. Three - dimensionally braided structural composites have distinct structure that is fully integrated, continuously spatial fiber - network impregnated with ductile material. the new innovative materials have not plies as conventional composites have, and put an end once and all to low interlaminar strength showing in laminate materials. because of their enhanced stiffness and strength in the thickness direction, near - net - shape design and manufacturing, superior damage tolerance and specified aerospace function, the braided composites are gaining more and more attention of industry and academia

    三維編織結構復合材料是完全整體、連續、多向的紡線（纖維束）的網路，充填以延性材料，這類新材料已失去通常復合材料的層合板概念，由此，層合板復合材料層間脆弱的致命弱點在編織結構復合材料中得到克服，所以編織結構復合材料具有高的強度和剛度（包括在厚度方向） ，接近實際形狀的製造，高的沖擊韌性、高的損傷阻抗，和按實際設計要求的特定的航空航天方面的使用功能，因而廣泛地受到工業界和學術界的關注。
  2. Laminate construction thickness

    結構層厚度
  3. It can measure shell speed and crusting of film laminating by adopting fks - 1 tester of film laminating capacity ; the principle of this instrument is that it makes film laminate on heating plate and turns 90or 180 of heating plate for moving un - shell sand. and then it measures shell thickness and observes cocking condition of surface sand

    採用fks - 1型覆膜砂結殼性能測試儀可以觀測覆膜砂的結殼速度和起皮狀況，其原理是將覆膜砂撒在加熱板上，經過某一時間之後，將加熱板旋轉90或180移去未結殼的鬆散砂，然後測量結殼厚度，並觀察表層砂的翹起情況。
  4. For laminate containing penetrated crack, " two planes " model is introduced to analyze the influence of repair parameters on the strength of repaired laminate, including such as patch size, patch thickness, patch layout, the location of rivets

    摘要針對含穿透性裂紋的損傷層壓板，採用「兩板」模型建立起機械連接修補結構有限元分析模型，分別計算補片大小、厚度、鋪排方式以及連接件位置等修補參數對修補效果的影響。
  5. For the laminate which contains a crack, the suggested patch shape is rectangle, the patch thickness is equal to the parent laminate and the patch stacking sequence is the same as the parent laminate. because the length and the width of the patch have the fewer influence on the repair effect, the patch has the least weight on the basis of enough edge distance, end distance and space having been promised

    ?對于含裂紋復合材料層壓板，長方形補片的長度和寬度對修補效果沒有非常明顯的影響，因此在保證連接邊距、間距和端距的條件下，補片大小的選擇應該以節省重量為原則；而當補片的鋪排順序與母板相同、相對厚度為100時能夠獲得比較好的修補效果。
  6. The residual strength of damaged composite laminates and their repaired structures are calculated, and the influence of the repair parameters is discussed by the finite element and program stated above. some useful conclusion can be drawn according to the curves, which show the influence of repair parameters to repair effect. for the laminate which contains a circle hole, the suggested patch shape is circle, the patch size is 2 to 3 times than the diameter of damaged hole, the patch thickness is equal to the parent laminate and the patch stacking sequence is the same as the parent laminate

    用所建立的二維有限元模型和編寫的有限元程序計算損傷板及其修補結構的剩餘強度，並分析了修補參數對修補效果的影響；根據本文計算得到的修補參數對修補效果的影響曲線，可以得到如下結論： ?對于含孔復合材料層壓板，當圓形補片與母板鋪排順序相同、直徑為損傷孔直徑2 3倍、相對厚度為100時能夠獲得比較好的修補效果。
  7. Laminate floor coverings - determination of thickness swelling after partial immersion in water

    層壓地板覆蓋物.部分浸水后的厚度膨脹測定
  8. In sso, the thickness of each stack of the laminate must be integer times as thick as that of single ply, the angle of each stack of the laminate is selected from a set of standard angles, and the stacking sequence can change arbitrarily. when material and ply angles of the laminate are selected, ga is used to giye the optimal laminate that meets the given requirements of thickness and geometry factors

    在550中，層合板各分層的厚度必須是單層材料厚度的整數倍，鋪層角取作一些標準的角度，各分層在層合板厚度方向上的相對位置可任意變化，利用ga求出滿足給定厚度和幾何因子要求的層合板最優鋪層結構。
  9. The main features of this system are : ( 1 ) design and calculate stable fiber paths fulfilling all technical requirements ; ( 2 ) update of the geometry of the mandrel surface with the increase of the thickness ; ( 3 ) the transfer of laminate data to fea - program for detail stress analysis ; ( 4 ) generation of the control data file for four axes winding and ( 5 ) the real time simulation of fiber paths and machine paths

    該系統主要特點有1 ）設計和計算穩定的纖維路徑； 2 ）隨厚度變化自動更新芯模曲面形狀； 3 ）為有限元分析提供路徑網格數據； 4 ）生成用於四軸纏繞機的運動控制指令數據以及5 ）纏繞過程三維圖形模擬。
  10. Parameters considered are : concrete compressive strength, percentage of flexural reinforcement, bonded length, thickness and stiffness of cfrp laminate and soon

    這些參數包括：混凝土強度、配筋率、粘結長度、 crfp厚度及剛度等，在設計過程中正確選擇參數可以避免加固梁發生脆性破壞。
分享友人
分享到 Line

分享到臉書