lifting height 中文意思是什麼
lifting height
解釋
上升高度-
Overhead travelling crane - span series and lifting height series
電動橋式起重機跨度和起升高度系列 -
Lifting and lowering of the pringting arm of this machine is vertical, therefore, in case of half - tone printing, presence of screen wire and consistency of aberration are improved ; in case of spot printing, stability and uniformity of inking are enhanced ; fine adjustment and lock of the worktable is independent of each other, so positioning error caused by lock of the worktable can be controlled ; height and pressure of the printing blade and ink - returning blade can be stepless - regulated separately, which improver printing quality and service life of half - tone ; printing travel and half - tone fixing mechanism can be fast adjusted, which is suitable for printing area with different size
本機印刷大臂升降為垂直升隆式，網線版印刷時網線表現率為色差一致性得到提高，實地版印刷的施墨穩定性及均勻性得以加強；工作臺微調與鎖緊獨立，因工作臺鎖緊而帶來的定位誤差得以控制；印刷刀、回墨刀高度及壓力均可單獨無級調節，提高了印刷質量和網版的使用壽命，印刷行程和網版固定機構大小可快速調節，方便不同規格的印刷面積。 -
The water level of the river networkcan be regulated effectively to meet crop demand, by controlling open time and lifting height of thetidal gate
通過調節擋潮閘的運行時間和開啟度，使該系統既能滿足排澇要求，又能合理控制河網水位，使之滿足農作物生長對地下水位的要求。 -
Tower crane has following characteristics : discontinuous working, starting & braking frequently ; there are noticeable vibration and impulsion in running ; high lifting height and extend rang, heavy lifting moment, etc. with the advent of more and more high - rise and large - scale buildings, requirements for the efficiency, lifting height, lifting moment, and safety features are becoming higher and higher
塔式起重機具有下述工作特點:斷續工作、頻繁啟動、制動;運行過程中有明顯的振動和沖擊;起升高度和工作幅度較大，起重力矩大。隨著社會中各類高層建築和大型工程的出現，使其對塔機的工作效率、起升高度、起重力矩和安全性等工作性能提出了更高的要求。 -
Note : ask the user about the height of lifting base they want
注意要問清顧客吊腳需要預留的高度 -
In order to overcome the weight of cable itself and voltage drop when lifting height is over 100m, we use cable trolley
為了克服100米以上提升高度時過大的電纜自重和電壓降，配有電纜滑車裝置。 -
Communicate with the user to confirm the height of lifting base. adjust the location of lifting base of door hinge. for suit door, adjust the lifting base of door hinge first
與用戶溝通確定吊腳高度，先調整門鉸位的吊腳，套門先調整后門鉸位的吊腳。 -
Presser foot lifting height
壓腳提升高度 -
Max lifting height mm
最大起升高度mm -
These trucks have following features and benefits, human system engineering design, continuously variable driver, wide view mast assembly made of germany steel, maximum lifting height 5. 2 meters, easy to assemble / dismantle storage battery, with optional standing plat
本機器採用人機工具設計、無級變速，德國進口型鋼精製寬視野門架，最大起升高度可達5 . 2米，電瓶可從三個方向裝卸，並可選配操作者隨機踏板。 -
It provides steady lifting with low noise, and is equipped with lifting brackets, anti - fall supporting protection, stopping protection against wire fracture, limiting device for maximum load, control device for maximum lifting height and fixing device for the turning angle of the bracket arm
升降平穩、噪音低，並設有舉升托架、防跌落支承保險、鋼索斷裂制動保險；最大負荷限定裝置和托臂回轉角度鎖定裝置。 -
Lifting height 1800mm
升降高度1800mm -
Lifting height mm
起升高度mm -
Max lifting height
起升高度 -
In recent years, lifting construction technology of our country have been greatly developed from the traditional method that is lifted by machine and controlled by hand to mulli - machine lifting using the integration of machine, electricity and liquid, which resulted in the component and equipment larger and heavier, the height of erection higher and the distance of sliding longer
特別近幾年來，我國結構吊裝技術得到了巨大發展和創新，大型構件與設備趨向更大、更重、提升高度更高、滑移距離更長，已從傳統的機械吊裝、手動控制向多機吊裝的機、電、液一體化，計算機控制方向發展。 -
In crane choosing, three parameters should be taken into consideration : payload capacity ( q ), lifting height ( h ) and working radius ( r ). and three parameters should meet design requirements at the same time
選擇起重機的型號原則是所選起重機的三個工作參數，即起重量q ，起重高度h和工作幅度（回轉半徑） r均需要滿足班組結構吊裝要求。
分享友人