limiting length 中文意思是什麼
limiting length
解釋
限界長度-
Abstract : by using the correlation analysis of cotton climatic output and temperature elements of different temperature types and different length periods of time in akesu cotton region, the results obtained indicate ( 1 ) using daily temperature elements of different length periods of time correlated with cotton climatic output is more useful, more reasonable and more easily in founding out optimum temperature elements with biological significance than using ten - days temperature elements ; ( 2 ) in three temperature elements of mean temperature, maximum temperature and minimum temperature, the effect of maximum temperature on cotton climatic output is the greatest, mean temperature is greater, and minimum temperature is the least ; ( 3 ) the low temperature in later spring and summer have some limiting effects on forming cotton climatic output in akesu cotton region
文摘:通過對阿克蘇棉區棉花氣候產量與不同長度時段、不同類型溫度要素的相關分析，結果表明： （ 1 ）採用不同長度時段的日溫度要素與棉花氣候產量進行相關分析，比採用旬溫度要素的工作更細致，更合理，更易找出對棉花氣候產量影響較大的有生物學意義的較佳時段和溫度要素； （ 2 ）在平均溫度、最高溫度及最低溫度3個溫度要素中，以最高溫度對棉花氣候產量的影響最大，其次是平均溫度，最低溫度最小； （ 3 ）春末及夏季的低溫對阿克蘇棉區的棉花氣候產量形成具有一定的制約作用。 -
The theoretical analysis shows that mz - ifog can be used to detect the rotation rate of moving objects. a systematic analysis of transfer characteristics of mz - ifog is made. performance - limiting factors, including the path - length difference, the disturbance of temperature fluctuation and stress from working environment, the quality of light source, are all discussed along with methods to reduce their effect on the output signal
本文用系統的方法分析了mz型干涉式光纖陀螺儀的光傳輸特徵，指出了其較大的非互易性因素-臂長差的存在，分析了工作環境因素（溫度，應力） 、光源質量（輸出光束中心波長、光功率波動及偏振態波動）對系統工作性能的影響，並指出了減少系統非互易因素、抑制噪聲、提高檢測穩定性的措施。 -
Limiting value for supporting length
支承長度限值47 -
The minimum requirement for sensitivity shall be such that a succession of not less than 20 breakdowns of the spark gap shall cause the fault indicator to register neither more nor less than one cunt per breakdown when the spark gap is open and is of the length shown above, with the current limiting impedance in series with the gap
在最底靈敏度測試的時候，應先接入上述要求的人工擊穿裝置，啟動人工擊穿裝置，使金屬板與金屬針間的火花間隙被連續擊穿20次，要求火花試驗機的擊穿計數器應記錄20次，對每次擊穿都應準確無誤地計數，不應多計也不應少計。 -
The minimum requirement for sensitivity shall be such that a succession of not less than 20 breakdowns of the spark gap shall cause the fault indicator to register neither more nor less than one count per breakdown when the spark gap is open and of the length shown above, with the current limiting impedance in series with the gap
在最底靈敏度測試的時候，應先接入上述要求的人工擊穿裝置， ，啟動人工擊穿裝置，使金屬板與金屬針間的火花間隙被連續擊穿20次，要求火花試驗機的擊穿計數器應記錄20次，對每次擊穿都應準確無誤地計數，不應多計也不應少計。 -
When the interaction length or gain coefficient is changed, the sbs threshold is changed, and the intensity value of optical limiting is altered
當改變相互作用長度或者介質增益系數，即可以改變受激布里淵散射的產生閾值，進而改變輸出脈沖空間限幅的幅值。 -
The second chapter analysis the way how to decide the length of the limiting flaw. according to the theory of fracture mechnics and damnification mechnics, and the author lakes two way for calculating the length of the limited flaw, in finally, two calculation result is identical, so we can draw a conclusion that the method that we used in the past is in consistent with reality
本文第二章分析了如何應用斷裂力學和損傷力學知識，用兩種不同的求解方法來確定臨界裂紋的長度，計算分析發現兩者結果一致，這說明我們所使用的確定臨界裂紋長度的方法和實際情況是一致的。
分享友人