link fault 中文意思是什麼
link fault
解釋
連接故障-
This paper discusses the designing and making of the dynamic testing systems of engine electronic control system. base on the construction and operation principle of santana 2000gsi m3. 8. 2 engine electronic control systems, design and manufacture led circuit of dynamic testing and fault imitating electronic control unit. on the inspect board, design and equip with motronic 3. 8. 2 ecu i / o measuring joints, design and set up obd - ii diagnostic communication link, design and install fuel pressure inspecting meter. depend on the obd - ii diagnostic communication link and ecu i / o measuring joints, this dynamic testing system can inspect engine electronic fuel injection system, distributorless ignition system, idle speed control system and evaporative emission control system, and can inspect m3. 8. 2 sensors, ecu and actuators, and can interrogate fault memory and erase fault memory ; and can analyse data stream ; and can carry out fault imitating. besides, this paper analyses sensors and actuators typical fault w aves
2電控單元電路連接器設計製成輸入輸出電子控制檢測端子，並在檢測面板上布置了obd -診斷插座和燃油壓力表。使該動態測試系統能實現對電噴發動機的燃油系統、直接點火系統、怠速控制系統和燃油蒸氣排放控制系統的動態檢測；並通過obd -診斷座、 ecu輸入輸出檢測端子和故障模擬處理單元實現對電噴發動機電控系統各傳感器、電控單元、執行器進行故障碼讀取與清除；動態數據讀取和波形測試和故障模擬等。此外，本論文還分析了傳感器和執行器典型故障波形。 -
Simultaneously, the san based on fibre channel - arbitrated loop ( fc - al ) has conveniece, expansibility, high fault tolerated ability, high reliability and agility of configuration, and supports heterogeneous servers such as unix, nt and netware to link at the same time so as to be able to reduce total holding cost
同時，基於光纖通道仲裁環技術（ fc - al ）的san具有管理上的方便性、可擴展性、高容錯能力、高可靠性和配置的靈活性，並且支持異構服務器unix 、 nt和netware同時連接，能夠有效地減少總體擁有成本（ tco ） 。 -
It is used to provide reference to operator of power plant. in recurrent composed bp networks, the relation of interior node is enhanced because the link weight of input layer and output layer are added, and the saturation of fault prediction is avoided by using the linear prompting function
本文所建的用於鍋爐故障預測的遞推合成bp網路由於bp網路各層之間及輸入層與輸出層之間的連接權的增加和線性激勵函數的採用，極大地加強了內部節點的關聯能力，避免了bp網路預測的飽和性的出現。 -
In order to use an exceptionhandler process to effectively handle an exception, you need to add a partner link to point to that process and then add an invoke activity in the fault handler, which links to the partner link, as shown in
為了使用exceptionhandler流程來有效的處理異常，需要添加一個合作夥伴鏈接，指向那個流程，然後在故障處理程序中添加一個調用活動，其鏈接到合作夥伴鏈接，如 -
The new oam protocols should have basic management regulations including link state testing, fault alert, loop back etc. in this paper, we implement oam protocols in both olt and onu by adding oam software function block
新協議應該加入諸如鏈路狀態檢測，錯誤發生警告，環回測試等規程來實現接入管理。本文主要研究了在olt和onu上加載軟體模塊來實現oam管理。 -
Presents starting link and system organization of fan ’ s inspects status and fault diagnosis. the system collects data through data acquisition system, inspects fan ’ s status with monitoring soft, establishes routine and fault data bases, and calls routine analysis daughter system, and in the end diagnoses the fault, observates equipment ’ s operating mode ; finds fault type and cause. with the assistance of the diagnosis system, the economy and safety of factory is greatly improved
通過數據採集系統對信號進行採集與處理，利用監測軟體實現風機狀態監測，建立常規數據庫和故障數據庫以及調用常規分析子系統進行故障診斷等手段，觀察設備運行狀態，找到故障的類型和原因，作為決策的依據，從而提高了設備的經濟性和安全性。 -
In this paper, on the base of analyzing the reliability operation status and the reliability data of 200mw units with the reliability management information system for jingyuan power plant, the feeble link and the key part of the generation set and system are defined and the corresponding measures are adopted, consequently, is increased the fault ratio of the device we can reduce and enhance security of the power plant, which is an effective method that controls the device reliability by using the mothod of systems engineering, namely plans, organizes, corresponds, controls and supervises the diversified engineering and technic activity of the reliability during the period of the whole device life to realize the reliability aim, minimize the cost of the whole device life and improve the general level of business safety production
本文在應用靖遠電廠可靠性管理信息系統對該廠的200mw機組運行狀況和可靠性數據進行分析的基礎上，確定了發電設備和系統的薄弱環節、關鍵部位、並採取相應的措施，從而使設備的故障率減少，使電廠的安全性得以提高。這是一種利用系統工程的方法對設備的可靠性進行控制，即對設備全壽命周期中各項可靠性工程技術活動進行規劃、組織、協調、控制、監督，以實現確定的可靠性目標，使設備全壽命周期費用最低，提高企業安全生產綜合水平的有效方法。
分享友人