liquid volume fraction 中文意思是什麼
liquid volume fraction
解釋
液相體積比-
The age hardening characteristic of as - cast cu20ni20mn and cu20ni35mn alloys and the interface characteristic between the alloy and cast tungsten carbide were studied, and on the basis of this study, composites of cu - ni - mn alloy reinforced with different volume fraction ( 0 - 45vol. % ) and different size ( 42 - 362 m ) of cast tungsten carbide particles were made by vacuum hot - pressing liquid sintering technology. pin on disk two body abrasion tests have been performed with different size of sic abrasive under different loads
本文研究了鑄態cu20ni20mn和cu20ni35mn合金的時效硬化特性及其與鑄造碳化鎢的界面特性，並在此基礎上以不同尺寸（ 42 362 m ）的鑄造碳化鎢顆粒為增強體，採用真空熱壓液相燒結技術制備了不同顆粒含量（ 0 45vol . ）的鑄造碳化鎢顆粒增強cu - ni - mn合金基復合材料；以不同粒度的sic為磨料，在不同載荷條件下利用銷?盤磨損試驗機測試了復合材料的二體磨料磨損性能。 -
Firstly, based on the present research all over the world, a 3d quasi - single phase model is built together with k - equations. the special feature of this model is taking account of the influence of interaction between liquid and gas, that is to say, the influence of interphase drag force, lifting force perpendicular to the relative velocity, virtual mass force and gas or liquid volume fraction in the fluid field have been considered. a 3d two - fluid model is also built in order to describe more accurately the fluid flow on distillation trays by comparing the computational results of quasi - single phase mathematical model with of two - fluid mathematical model
本文在國內外已有的研究基礎上，首先建立了以k - （封閉模型為基礎的三維擬單相流模型，該模型的特點在於充分考慮了氣液兩相間相互作用的影響，即計入了相間曳力、橫向升力、虛擬質量力和氣、液相含率對流場的影響；並建立了塔板三維雙流體模型，主要目的是通過對比擬單相流數學模型、雙流體數學模型的計算結果，建立能夠準確描述塔板上流體流動的數學模型。 -
Three models are proposed as follows by applying the model of " mixed flow " : the stress of increasing fluid on fouling, collision between solid particles and fouling, and solid particles movement velocity ; the effects of operating parameters, properties of particles, and the volume fraction of particles on stress in solid - liquid two phase flow, collision stress between solid particles and fouling, maximal contacting area between solid particles and fouling and maximal contacting time between solid particles and fouling are investigated systematically by calculating and theoretical analysis
利用「混流」模型，建立了兩相流體的剪應力模型、固體顆粒與垢層的碰撞模型和固體顆粒的運動速度模型；通過計算和理論分析，系統地考察了操作參數、顆粒物性、顆粒體積分率等對固液兩相流剪應力、顆粒對垢層的碰撞力、顆粒與垢層的最大接觸時間和最大接觸面積的影響。 -
Secondly, for the first time, by volume average concept and reynolds time - average method, a 3d quasi - single phase mass transfer model of distillation tray is deduced by considering the effects of velocity fluctuation, concentration fluctuation and volume fraction of gas and liquid on mass transfer. a source item sc for interphase mass transfer is considered. by applying conventional method of estimating the interphase mass transfer coefficient, a formula for sc is obtained
其次，採用體平均概念、雷諾時均化方法結合塔板氣液相互作用的實際情況首次推導了考慮速度、濃度脈動項和氣、液相含率影響的塔板三維擬單相流湍流傳質模型，源相中考慮了氣液相間傳質項sc ，並運用化工中關于相間傳質系數計算的理論，推導了sc的表達式。 -
The results indicate that the fiber radius, infiltration pressure, liquid metal viscosity coefficient and the volume fraction of perform affect the infiltration velocity of liquid metal and the infiltration process
對模擬結果分析研究表明，纖維半徑、浸滲壓力、液態金屬粘度系數和纖維預制體的體積分數等影響液態金屬的浸滲速度及浸滲過程。
分享友人