locking angle 中文意思是什麼

locking angle 解釋
嚙合角
  • locking : 打開或關閉文件共享鎖
  • angle : n 【英史】盎格魯人〈cf Angles〉。n 1 角，隅，角落；棱，嬗角。2 【數學】角，角位，角的度數。3 【機...
  1. Aimed at design index of input power 1. 5kw, most output rotate velocity 300rpm, and rating output rotate velocity 150rpm, considering factors of angle and ratio of transmission, on the basis of kinematics simulation, author optimized the kinematics parameters. in this paper, author has made some analysis and study to the primal assembly condition of transformer ' s sequential action in theory, designed structure dimension of the input and output transformer, and verified the corresponding strengthen. further, the structure, which is to key transmission components of velocity control system of the speed regulator, has been designed based on meeting operational sensitivity, precision and self - locking

    本文針對輸入功率為1 . 5kw ，最大輸出轉速，額定輸出轉速的無級變速器的設計要求，並考慮到傳動角及變速比等因素，在運動學模擬的基礎上，對運動學參數進行了優化；本文對變換器連續作用的初始裝配條件進行了理論分析與研究，對輸入、輸出變換器作了結構尺寸的設計，並進行了強度校核計算；本文還對變速器調速系統中主要傳動構件在滿足操作的靈敏度、精度、自鎖性的基礎上進行了結構設計；最後採用workingmodel3d軟體，進行虛擬樣機的計算機輔助模擬設計及運動學和動力學計算。
  2. Analyze item by item the position of unintact cycle, the running clearance of unintact cycle, locking - deform, datum dimension regulating, repeatly install, power voltage wave and marking running etc. at the same time, we give the calculating formula to calculating the running marking random error, and use it to calculate the system error of big diameter measure instrument - - datum dimension frame error, gyro - wheel diameter error, error caused by circumstance temperature, error caused by backing distance, angle error, delay error of data collecting circuit, lathe main shaft running error, workpiece install partial error

    對不完整圓的位置、不完整圓的轉動間隙、鎖緊變形、基準尺調整、重復安裝、電源電壓波動、標記轉動等隨機誤差進行了逐項分析，並給出轉動標記隨機誤差的計算公式。對大直徑測量儀的系統誤差?基準尺尺架誤差、滾輪直徑誤差、環境溫度引起的誤差、後退距離引起的誤差、角度誤差、數據採集電路延時誤差、車床主軸回轉誤差、工件安裝偏心誤差分別進行了計算，最後對誤差進行合成。
  3. Mc 15ra right angle housing for 15a, 20a straight 15a locking plugs connectors, black, enable wiring in 8 cover orientations, holds for cable up to 17mm dia

    適用於15a ， 20a直型， 15a鎖式插頭和連接頭，黑，最多8方向調整角度， 17mm內線徑使用可以
  4. Self - locking, floating, right angle anchor nuts with mj thread

    Mj螺紋直角游動板自鎖螺母
  5. Spacers for self - locking nuts, angle, anchor

    角形托板自鎖螺母墊片
分享友人
分享到 Line

分享到臉書