lower tooth 中文意思是什麼
lower tooth
解釋
下齒-
The results indicate that a stable deformation localization band occurs in the coal cutting course and develops to macroscopic crack ; the deformation localization band is slantwise ; while the cutter tooth is used, the deformation localization develops slowly, and the localization becomes wider and the strain value in the band area higher afterwards ; when the point - attack pick used the localization develops quickly and the localization band becomes narrow and the strain value in the band lower
研究表明：截齒截割煤體過程中，煤體出現穩定的變形局部化帶，且最終發展為宏觀裂紋；煤體變形局部化帶為一個傾斜帶：刀齒截割時，變形局部化發展較慢，但產生變形局部化后，局部化帶寬且帶內應變值較高；而鎬齒截割時，變形局部化發展較快，但產生局部化后，局部化帶窄且帶內應變值不如刀齒高。 -
For an orthodontic case with the discrepancy of the discoordination between the length of palate bone and tooth size or for a case with skeletal discrepancy of the unsymmetry upper and lower jaw in their size and position, the most common treatment is to extract the upper ahd lower first or the second premolar
摘要一般矯正治療，對于齒槽骨和牙齒大小長度總和的不調和或上下顎骨骨骼性大小、位置不對稱，其處置原則通常都以上下顎第一小臼齒或第二小臼齒等4齒做為拔除對象來進行矯正治療。 -
The upper and lower jaws possess straight tooth rows and the jaw arches are almost rectangular in shape.
上、下頜具有直的齒列，而頜弓幾乎呈直角形。 -
The knowledge on the properties of used materials is urgently needed for reasonable life - prediction and life - distribution. as cylinder bolts are concerned, they often rapture at the first tooth - root resulting from lower high temperature strength of their material and higher stress. since bolts operate at high temperature environment, creep skew and damage causing their failure are important factors that can not been neglected
就汽缸螺栓而言，由於螺栓材料的高溫強度偏低，預緊力過大，常常在螺栓的第一齒根部位發生蠕變脆性斷裂，因其長期在高溫環境下工作，蠕變變形和蠕變損傷是其失效的一個不可忽略的重要因素。 -
The research result shows that the motor ' s torque will improved in lower voltage, when tooth width are not equal, and magnet conductivity of material is high
研究結果表明，當專用電機採用不等齒寬結構，或採用高磁導的軟磁材料時，均有利於提高電機在低電壓下的輸出轉矩。 -
Translation modes are similarly independent of the rotational support stiffnesses. large contact ratio do not mean lower mesh force. if either the number of sun or ring gear is not multiple of planet gear, system will run effectively, with lower impaction of tooth mesh in and out
研究表明：扭轉支撐剛度的變化影響系統的轉動模態，徑向支撐剛度（行星架的除外）的變化影響系統的位移模態；齒輪間重合度大並不等於輪齒間的受力情況好；行星輪與內齒圈齒數不為行星輪個數的整數被時，輪齒的嚙入、嚙出對系統的沖擊小，系統的效率高。 -
This paper deduced the involute gear total tooth profile equations of unsymmetric teeth with double pressure angles, proposed the calculation formulas of coordinates and load angle at the upper and lower points of single and double teeth mesh areas, and programmed the relevant parametric programs
摘要推導出雙壓力角非對稱漸開線齒輪系統全齒廓方程，以及在單、雙齒嚙合上、下界點處坐標和載荷角的計算公式，編制了相應的參數化程序。
分享友人