mathematical-model calculation 中文意思是什麼

mathematical-model calculation 解釋
數學模型計算
  • mathematical : adj 數學（上）的，數理的；嚴正的，精確的。 mathematical instruments 制圖儀器。 mathematical logic...
  • model : n 1 模型，雛型；原型；設計圖；模範；（畫家、雕刻家的）模特兒；樣板。2 典型，模範。3 （女服裝店僱...
  • calculation : n. 1. 計算，計演算法。2. 推定，預測。3. 深思熟慮，精打細算；慎重的計劃；算計。
  1. This paper analyzes the groundwater discharging course using fluidics theory and combining quay structure construction ; sets up the method of fast drainage by the dint of pipeline and blind ditch of fragment stone ; and gives the computational mathematical model for quay drainage and calculation formula for drainage process according to the principle of conservation of mass and underground percolation, which have been applied for quay ' s stability design and calculation

    應用流體力學理論結合碼頭結構建設，分析了地下水排泄過程，藉助管道和碎塊石盲溝建立了港口碼頭快速排水與擋墻基床排水的方法；運用質量守恆定律和地下水滲流原理，建立了港口碼頭排水計算數學模型和排水過程計算公式，並用在了碼頭的穩定設計計算中。
  2. This paper explores physical essence of overrunning clutch torsion stiffness, builds torsion stiffness mathematical model and give calculation method of torsion stiffness in miler overrunning clutch

    摘要分析了滾柱式超越離合器扭轉剛度的物理本質，建立扭轉剛度的數學模型，給出了滾柱式超越離合器扭轉剛度的計算方法。
  3. In this paper, starting from the basic law of fluid me chanics, a mathematical model equation for describing the tran sient flow of the wet gas in the pipeline under peak shaving op eration is established, a simplified treatment for the model equa tion is made and a train of thought for concrete calculation is de signed

    文章從流體力學的基本規律出發，建立了描述濕天然氣管道輸送調峰工況下瞬變流的數學模型方程，並對模型方程作了簡化處理，設計了具體的計算思路。
  4. Mathematical model for temperature distribution calculation during wheel quench heating process is established and used in the simulation of a certain type wheel

    摘要根據馬鋼車輪淬火加熱爐的實際狀況，建立了車輪淬火加熱過程溫度場計算模型。
  5. The improved scheme can ensure the south branch to be open to navigation and the flow here not to be broken in low water seasons, and it will have active effect on protecting the south branch and fuyuan town. this study is an attempt of applying three - dimensional mathematical model in analogue calculation and analysis of flow, sediment and riverbed movements in a long river reach. it is very important for the future thorough research, and has great significance for promoting the application of the three - dimensional model to resolve

    本研究是三維數學模型對較長河段水流、泥沙、河床運動模擬計算分析的一次嘗試，其對今後進一步深入研究和應用三維模型解決工程實際問題，完善模擬方法、提高模擬水平，真正發揮數學模型其省時、省力、靈活方便和模擬細膩等在研究水沙運動規律和河床變形等方面研究中優勢具有重要的意義。
  6. At the same time ， the fluid atomizing mathematical model of particle diameter and particle quantity were established ， and also the analogy calculation of particle diameter and particle quantity were carried out. the feasibility is verified that the fluid atomizing mathematical model can make prediction on the atomizing performance of pesticide. these will provide scientific foundation and deinsectication technology for the development of precise agriculture

    同時研究開發了粒徑與粒數的液體微粒化計算模型，並對噴霧機和煙霧機進行了粒徑與粒數的模擬計算，驗證了液體微粒化計算模型對農藥微粒化性能預測的可行性，為精準農業的發展提供了科學依據和防除技術。
  7. According to the stress wave theory on explosive exploding propagating in the rock, it builds up mathematical model of fractural ranges in the rock, and carry out actual calculation and analysis on fractural range of bench shooting in deep - hole. as a result of calculation, the lateral and bottom fractural range are about 1. 9m

    根據炸藥爆炸在巖石中傳播的應力波理論，建立巖石爆破破裂范圍數學模型，並對深孔梯段爆破破裂范圍進行了實行計算分析，計算結果為：混裝乳化炸藥巖石深孔梯段爆破側向底部破裂范圍為1 . 9m 。
  8. Different equations to corresponding components are presented by analysing and transformating the general equations of fluid routes, then static characteristics mathematical model of liquid propellant space propulsion system is presented. based on the data of static characteristics calculation, mass model of thruster, propellant, propellant tank, gas, gas bottle, pipe and valve is presented using both the method of statistical regression and the method of stress analysis, then corresponding mass model is presented. based on the characteristics of liquid propellant space propulsion systems, analyse the five phases ( concept and definition, design and improvement, manufactureing and arrangement, operation and ma intenance, disposal ) in which life cycle cost of liquid propellant space propulsion systems is cost separately, then discompsed structure of life cycle cost and model of life cycle cost are presented

    將組件分成氣路組件和液路組件，再對氣路組件和液路組件進行相應的分類，然後通過對通用流路方程進行分析和變換對不同類型的組件分別建立不同的方程，從而建立了一個適用於液體推進劑空間推進系統的靜態數學模型；根據靜態計算所得到的數據，應用統計回歸法和應力分析法分別建立推力室、推進劑、推進劑貯箱、氣體、氣瓶以及導管和活門等的質量模型，從而建立相應的質量模型；結合液體推進劑空間推進系統特點，對液體推進劑空間推進系統全壽命周期費用發生的五個階段（概念和定義、設計和改進、製造和安裝、運行和維修、處理）分別進行分析，建立了液體推進劑空間推進系統全壽命周期費用分解結構和全壽命周期費用模型。
  9. In the second part, firstly, the mathematical model for predicting hydrodynamic characteristics of varivec propeller under steady or unsteady condition are present, based on the general propeller lifting - surface theory, potential flow theory and green theorem. then, theoretical calculation methods for predicting hydrodynamic characteristics of varivec propeller designed above paragraphs are present, based on the finite basic solution method, the unsteady vortex lattice method and hess - smith method

    在理論計算部分，本文首先基於常規螺旋槳升力面理論、勢流理論和格林定理建立了定常和非定常狀態下全方向推進器水動力性能計算的數學模型，然後利用有限基本解法、非定常渦格法和赫斯?史密斯方法對全方向推進器定常和非定常狀態下的數學模型進行了數值離散，接下來針對前面所設計的全方位推進器進行了數值預報。
  10. The study has completed the design of two - phase inverter and made up of the two - phase inverter - motor system for experimental use it is a variable frequency adjustable speed system with a open - loop control of rotational speed, which consists of voltage - controlled oscillator circulating assign device inverter circuit and two - phase induction motor a accurate mathematical model is set based on the whole system, and simulator program of dynamic and steady condition is established, which is used to calculate the dynamic and steady performance by kron and symmetrical coordinate converter by simulator calculation and experimental research with specific parameter of the system, a comparison is made between predicted and experimental characteristics, experimental measurements are shown to compare closely with corresponding theoretical result it is compared with some variable frequency adjus table speed system comprising inverter and single - phase induction motor from the system efficiency torque pulsation and the effect of two - phase inverter capacitance based on the conclusion, harmonic cancellation pulse width modulation control of a two - phase inverter - fed induction - motor drive system is researched, which cancelled the low harmonic and improve the system performance

    通過對電機的kron變換和對稱分量變換，建立了系統較精確的數學模型，編制了系統動態及穩態運行的模擬計算程序分別計算系統的動態和穩態性能。通過對系統的具體參數進行了模擬運算和實驗研究，實驗和模擬結果進行比較，說明實驗和理論較為一致，並從系統效率、轉矩脈動及兩相逆變器電容的影響等方面與各種逆變器和單相異步電動機組成的變頻調速系統加以比較。在此基礎上，對兩相逆變器供電-異步電動機系統使用諧波抑制pwm控制進行了研究，由於減少了低次諧波，改善了系統性能。
  11. This paper evaluates the underground water resources and its safe levels of miming, and then studies the availability of molepipe drainage, a kind of practical underground water regulation technique. starting with the elevation of underground water resources and a safe level of mining through variable system theory, this paper analyzes the conditions of underground water resources based on the well - studied determination method of determining the two hydrographical coefficients : rainfall infiltration replenishment rate and irrigation replenishment rate. then considering irrigation, rainfall, drainage and other related factors, a mathematical model is set up for the calculation of underground water storage, exploitation on water regulation

    論文從灌區的地下水資源及其可開采量評價分析方面入手，在對兩個主要的水文地質參數即降雨入滲補給系數、灌溉入滲補給系數確定方法研究的基礎上，對灌區的地下水資源狀況進行分析，依據灌區的灌溉、降雨、排水條件及各種現狀因素，建立了地下水資源量計算的數學模型，西安理工大學工程碩士專業學位論文計算得到青銅峽灌區地下水的最大補給量和可開采量;另外對在開發利用地下水資源過程中的地下水位的調控進行了初步的探討，在銀北灌區開展對暗管排水調控地下水位的試驗研究。
  12. Abstract : the mathematical model of reliability design for shaft rigidity was established based on reliability inference theory. reliability calculation of cylinder shaft rigidity of press was proceeded and regularity of cylinder shaft rigidity reliability as the condition change was found

    文摘:應用可靠性設計相干理論建立了軸的剛度可靠性設計的數學模型，著重探討印刷機印刷滾筒軸的剛度可靠度的計算，並得出不同條件下印刷滾筒軸剛度可靠度的變化規律。
  13. By the comparison and analysis of different theory calculations and test results, the evaluation of theory calculation methods for analyzing mechanical characteristics of permanent magnet bearings is made : the calculation of static magnetic circuit is simple, which owns less mathematical model parameters, but its accuracy is not high

    通過將各種理論方法和試驗結果進行比較和分析，對各種永磁軸承力學特性的理論方法進行了評價。得出了以下結論:靜磁路法計算過程簡單，數學模型的參數少，但計算精度不高。
  14. Three mathematical models are presented to express the characteristics based on the systematical analysis of mechanical, hydraulic and fluid dynamic characteristics during three transient process, and numerical calculation methods are carried out to the three mathematical models. with the rigid water hummer theory and hydraulic characteristics, this paper has improved the boundary condition equation at pump during the suspending period, and drew a simplified mathematical model

    針對大型低揚程泵站過渡過程的具體特點，利用剛性水錘理論，對事故停泵時泵處的邊界條件方程進行改進，並結合泵裝置水力特性，得出大型低揚程泵站停泵過渡過程簡易計算方法的數學模型；針對具體數學模型編製程序進行計算求解。
  15. Thirdly, several problems are discussed, such as the calculation of the silting velocity of sediment, the sediment transport capacity, the coefficient of sediment resume saturation, etc. on the basis of these discussions, the mathematical model is improved

    其次對泥沙沉速計算、水流挾沙力和恢復飽和系數的取值等問題進行了探討，在此基礎上對現有的泥沙數模學型進行了改進和完善。
  16. The paper formulates the dynamic analyses of hydraulic operating mechanism in large space, established mathematical model, presents methods of differential equation system, and corrects its parameters concerned in process of solution. after the unloaded characteristics calculation and test under real condition are developed for type lw - 252 breaker equipped with hydraulic operating mechanism, the time - displacement cures and the velocity - displacement cures are obtained

    本文對液壓機構的速度分析，用了大量的篇幅，建立了數學模型，給出了其方程組的求解方法，並對求解過程中所涉及的系數給予修正，在此基礎上對本課題研製的配液壓機構lw - 252斷路器進行了實際條件下的空載特性計算及實驗研究，獲得了斷路器的時間? ?位移曲線和速度? ?位移曲線。
  17. On the basis of the analysis of fundamental principle of thermoelectric refrigeration, the steady state mathematical model of the thermoelectric system was founded. according to the model, the theoretical analysis and calculation are made on various working conditions, and analyzed theoretically the effects on thermoelectric system which caused by hot and cold temperature difference, the device ’ s effective system figure of merit, the properties of the heat changers, which established theoretical basic for the opening up and design of the thermoelectric system and its performance test

    在分析熱電製冷基本原理的基礎上，建立了熱電裝置的穩態系統數學模型，並依據該模型對熱電裝置系統進行了不同的工作狀態下的熱力分析計算，並就熱電裝置的冷熱端溫差、電堆片的優值系數、散熱器的散熱性能與熱電熱泵裝置性能的影響進行了理論分析，為熱電裝置的開發設計和現有熱電裝置的性能測試建立計算理論基礎。
  18. For a class of shunt - wound active power line conditioner, based on analysis of mathematical model of system and target of control, the algorithm of fuzzy variable structure sliding mode control is presented. the control algorithm can avoid complicated calculation of harmonic electric current in traditional control algorithm, and realize the feedback control of electric current. the algorithm is simple and easily implemented

    針對一類並聯型有源電網調節器在分析系統數學模型和控制目標的基礎浙江大學博士學位論文上，提出了模糊滑模控制策略，避免了傳統控制方法中復雜的諧波電流計算，實現對電源電流的閉環控制，該演算法簡單、易於實現，模擬結果證實了變結構滑模控制的有效性。
  19. Under certain conditions, the calculating formula of interlayer stress and the stress - distributing diagram in cut planes are provided, and the mathematical model for warpage deformation calculation is also established

    建立了翹曲變形的數學模型，討論了各種工藝參數（層數、掃描線長、成型室溫度、層厚等）對翹曲變形量的影響。
  20. According to the analysis of the gate, the author put forward a mathematical model of the optimization design of the hydraulic automatic tilting gate, and then worked out the structural stability optimization design program of the hydraulic automatic tilting gate. then by the calculation of the program, a better design for a certain project was gained

    根據對翻板閘門的運行分析，提出了翻板閘門優化設計數學模型的一般表達式，並據此編制出水力自動翻板閘門的結構穩定性優化設計程序，對某一工程實例，通過程序的計算，得到了較理想的設計成果。
分享友人
分享到 Line

分享到臉書