matrix powder 中文意思是什麼
matrix powder
解釋
紙型粉-
The technique of producing metal matrix composite include powder metallurgy, casting ( including stirring casting process, in situ contact reaction process, liquid - phase metal infiltration process, co - spray deposition forming process ), reaction mechanic alloying process
制備金屬基復合材料的工藝分為粉末冶金法、鑄造法（鑄造法細分為攪拌鑄造法、原位接觸反應法、液相浸滲法、共噴射沉積法） 、反應機械合金化技術。 -
In this paper, nanosized al2o3 ceramic particles were chose as reinforcing phase. enhanced with ultrasonic wave the particles were covered with copper using method by electroless plating, the copper - matrix composite was developed by hot - press sintering process of the composite powder. the composition, microstructure, hardness, density and dry sliding wear property of the new material have been studied
研究路線為：選用納米級al _ 2o _ 3陶瓷顆粒作為增強相，在超聲波的環境中用化學鍍的方法完成對納米al _ 2o _ 3陶瓷顆粒表面的金屬銅包覆，採用熱壓燒結成型技術以復合粉末為原料制備成納米al _ 2o _ 3陶瓷顆粒增強銅基復合材料，研究分析復合材料的成分、組織結構、硬度以及緻密度，對試樣進行了干滑動摩擦磨損實驗。 -
2 sintering equipment of powder metallurgy products : iron / copper matrix push rod type sintering furnace, net strip sintering furnace, rapidly cooling vacuum sintering furnace ( patent awarded ), high temperature molybdenum wire sintering furnace, equipment of titanium coating on diamonds
粉末冶金製品燒結設備：鐵/銅基推桿式燒結爐，網帶燒結爐，內置式快冷真空燒結爐（專利產品） ，高溫鉬絲燒結爐，金剛石鍍鈦設備。 -
In this paper, a series of ultra - fine fly ash composite powder ( cufa ii ) products for rapid repair are researched and developed successly with the ultra - fine fly ash as matrix. cufa ii can replace cement equivalently more than 30 %. high performance rapid repair concrete ( hprrc ) in which cufa ii replaces cement equivalently more than 30 % can meet the requirements of opening traffic within 12 ~ 48h, which solves the problem of opening traffic as soon as possible after damaged portland cement concrete pavement are repaired for a whole plate, and the engineering cost is lowered greatly
本文以超細粉煤灰為基材，研製並開發出粉煤灰復合超細粉快速修補專用摻合料（ cufa ）系列產品，等量取代水泥30 ，配製的高性能快速修補砼（ hprrc ）在12 48h內達到開放交通的要求，解決了破損的水泥砼路面整板翻修后快速開放交通這一問題，並大大降低工程成本。 -
And pbo single crystal nanowire was successfully prepared with new method. the results show that the amorphous matrix of the powders almost completely transforms into crystalline perovskite phase after 600 calcinations. the mean grain size in pt / tb powder is about 23nm that is smaller than that of pt powders
鈣鈦礦相的晶軸比c / a比未摻tb的pt粉末低，具有贗立方結構的特性，降低了從立方相向這種四方相轉化的勢壘，從而有效地抑制了較高溫下焦綠石相的產生。 -
Because of the doped ions sr2 + and sn4 + entering into the matrix lattice evenly and crystallizing completely, the sintered ceramics of the nano - sized powder have dielectric constant ten times higher and dielectric loss sixty percent lower than those of pure batio3 phase at room temperature
降低，而且室溫介電常數比batio3純相提高近ro倍，而介電損失降低到1 / 8 ，燒結溫度比傳統微米級粉體的燒結溫度降低150一200 。 -
The matrix and the gel, powder and pellets of composites are characterized by ir, dta, xrd, sem. the following is the results : at the transition process, existing the polymerization of si ( oc2h5 ) 4 and citric slats. ( 2 ) the transition temperature of the drier gel to powder at 400 - 600. ( 3 ) the solid solution matrix of li3. 4sio. 4v0. 6o4 has the structure of li3vo3 ( high temperature phase ). t
固溶體具有li人o3高溫導電相結構：第二相氧化物或埋鹽主要以玻璃態的形式存在於燒結體的晶界，既作為燒結助劑加速了燒結的進程，得到了均勻的、緻密的燒結0體，同時又使材料的晶界電導率得到提高。 -
The characteristic of stirring equipment is used a shaking sieve to disperse the adding pure fe or fe203 powder and used a combined stirrer instead of a common paddle stirrer to improve the shear effect to mixing melts. the particularity of fabricating process is the step of holding stirring at a constant high temperature. both of which can improve the even distributing degree of reinforcement phase in pure al matrix
攪拌設備的特殊之處在於使用了振蕩篩分散加入粉末和更換組合式攪拌器來提高對混合熔體的剪切效果，工藝的特別之處在於一定溫度下的保溫攪拌過程，這二者均能提高強化相在純al基體中的均勻分佈。 -
In addition, under high sintering temperatures, iron powder can result in the graphitization of diamonds. these two reasons will affect the mechanical properties of the metal bond and its retention capacity. as a result, the wear resistance of metal bond is poor and diamond grits can be easily pulled out from the matrix, thereby shortening the life of the saw - blade
而且在高溫下，鐵粉會對金剛石產生較嚴重的化學侵蝕，這兩方面的原因都會影響結合劑本身的力學性能及其對金剛石的有效把持，導致鋸切過程中結合劑耐磨性差，金剛石容易脫落，使鋸片壽命縮短。 -
The partial liquid phase during superplastic deformation of 2024 aluminum alloy - matrix composites reinforced with sic particulates ( pm - sic ( subscript p ) / ly12 ) by powder metallurgical ( pm ) processing was studied usina sem etc
摘要用掃描電鏡等方法對碳化顆粒強化ly12鋁合金基復合材料超塑變形時出現的局部液相現象進行了研究分析。 -
Tic0. 7n0. 3 particulates reinforced titanium matrix composites and components prepared by powder injection molding
3顆粒增強鈦基復合材料和零件 -
A full - scale review of the nonmetal mineral filler to improve the strength and toughness of the resin matrix materials in the domestic and overseas is presented. based on the theory and experiment, the mechanism of the fsmf filler to build up the strength and toughness in the resin matrix composite materials is studied ; the relation of the mechanical property of the resin cast and the content of the fsmf is obtained ; the elasticity modulus of the fsmf powder is estimated by analysis method and cmm method ; in the end, fsmf used in rpmp is discussed
本文對非金屬礦物填料填充樹脂復合材料增強增韌的國內外研究現狀進行了較全面的評述；在理論和實驗的基礎上，研究了fsmf填充樹脂復合材料增強增韌機理；進行了fsmf填充樹脂澆鑄體的有關力學性能測試，獲得了fsmf填充樹脂澆鑄體的有關力學性能與fsmf含量的關系；利用解析法和cmm法，估算了fsmf粉體的彈性模量；最後探討了fsmf在玻璃鋼夾砂管道中的應用。 -
The present paper summaries the origin of the infrared radiant coating, the constituents of matrix of the radiant powder and the carrier adhesive, as well as the process of development and application of the infrared radiant coating, and analyzes factors affecting an extensive utilization of the material and discusses the application prospect and trend of development
對紅外輻射塗料的起源、輻射粉體基料的組成、載體粘結劑的組成、塗料的應用與發展過程進行了綜述，分析了影響紅外輻射塗料推廣應用的原因，探討了其應用前景和發展趨勢。
分享友人