measurement bias 中文意思是什麼

measurement bias 解釋
測量偏倚
  • measurement : n. 1. 測量，計量，量度。2. 份量，尺寸，大小，寬度，厚度，深度（等）。3. 測量法。 measurement goods （按體積、容積計算的）體積貨物。
  • bias : n 1 成見，先入之見，偏執，偏見 （opp Impartiality ）; 傾向，嗜好；癖 （towards）。2 （衣服等上面...
  1. The measurement results from interdigitated capacitors demonstrated that the tunability is 21 % when the bias is 40v and the loss is 0. 25 %

    對于叉指電容器結構，當外加直流偏壓為40v時，調節率為21 % ，介電損耗低至0 . 25 % 。
  2. The sources of uncertainty components are analyzed through the analysis of the mathematic model of measurement system. furthermore, the change of measurement system bias is pointed out as the main reason which leads to the dynamic change of uncertain with the research on the element of dynamic uncertainty combined with the research of the law of metrological property variation of measurement system. it makes the academic model of dynamic uncertainty available

    通過對測量系統數學模型的研究，分析了測量不確定度分量的來源，進一步結合測量系統量值特性的變化規律，對測量不確定度的動態機理進行了研究，指出測量系統偏差的變化引起的不確定度分量是測量系統的結果的不確定度動態變化的主要原因，從而得到動態不確定度的原理模型。
  3. Aperture synthesis uses interferometry technique to improve the limitations set by antenna physical aperture while working at lower frequency. phase and amplitude calibration of the visibility samples must be carried out to compensate for system bias before measurement

    綜合孔徑技術利用了以小口徑天線陣列合成大的觀測口徑的技術，解決了在較低頻率時天線物理口徑要足夠大才能得到期望的空間解析度的嚴重缺陷。
  4. The principal needs of realization on strategic inertial accelerometer are large measurement range ( higher than 70g ) and high stability. in this paper aimed at a most basic and typical " sandwich " structure with easy realization in techniques, the system of micromachined electrostatic servo - accelerometer is analyzed in detail on static and dynamic state, mainly including : the influence on the z - component of the center of mass, lateral accelerations disturbance and the applied bias voltage on the stability of the sensor

    戰略慣導加速度計實用化的首要條件是大量程（ 70g以上）和高穩定性，本文針對一種最基本、最為典型和工藝上較易實現的「三明治」結構，從靜態和動態兩方面對電容式微機械靜電伺服加速度計系統進行了詳細分析。
  5. The electro - chemical measurement system used to perform dpsv measurement is constructed with two parts, a low - current measurement system consists of low input bias current operational amplifier and a high resolution sar adc and a potentialstat consists of high resolution dac and high current buffer amplifier

    對于微分脈沖伏安溶出測量，我們使用高精度高速saradc和低偏置電流運放構成微電流采樣系統，使用高精度dac和高速大電流緩沖放大器設計了恆電位計，並與微控制器共通組成電化學測量系統。
  6. The last, taking into account of the nonlinear transformation from sphere frame to cartesian frame, maneuvering target tracking is simulated by using current statistical model and converted measurement kalman filter ( cmkf ) without linearization bias in the statistical condition. the paper presents the converted measurement covariance that determines when to use the current measurements vs. the predicted state, and the simulation results are satisfied

    最後，針對球坐標系與直角坐標系之間的變換是非線性變換的特點，哈爾濱工程大學博士學位論文運用統計條件下不存在線性化誤差的轉換測量卡爾曼濾波演算法，結合「當前」機動模型對機動目標進行了模擬研究。
  7. Process - dissociation procedure ; pure measurement ; sampling bias ; memory ; consciousness

    過程分離程序純凈測量取樣偏差記憶意識
  8. In the dissertation, the effects of bias voltage polarity on the measurement and the normal operation are deeply researched when the voltage polarity is positive - positive, negative - positive and negative - negative respectively. the results are compared with the ones studied by others when the voltage polarity is positive - negative. the air damping of the laterally driven microstructures is slide - film air damping

    本文通過改變偏置電壓極性分別為正?正、負?正、負?負，並和偏置電壓極性為正?負配置時進行對比，深入研究了電容式傳感器在不同偏置電壓極性下，驅動信號產生的靜電力對傳感器檢測和工作性能的影響。
  9. Given a properly collected set of data, the six sigma black belt should be able to perform a complete measurement system analysis, including the calculation of bias, repeatability, stability, discrimination ( resolution ) and linearity

    譯文：給出一組適當的現成數據，六西格瑪黑帶應該能夠完成測量系統分析，包括計算偏倚、重復性、再現性、穩定性、辨別力（解析度）和線性。
  10. Given a properly collected set of data, the six sigma black belt should be able to perform a complete measurement system analysis, including the calculation of bias, repeatability, reproducibility, stability, discrimination ( resolution ) and linearity

    給出一組適當的數據， 6西格瑪黑帶應能完成測量系統分析，包括計算偏倚、重復性、再現性、穩定性、辨別力（解析度）和線性。
  11. A review of bias in attitude measurement

    態度測量偏差研究
分享友人
分享到 Line

分享到臉書