measuring truck 中文意思是什麼

measuring truck 解釋
儀表車
  • measuring : n. ,adj. 測量（的），測量用（的）。 remote measuring 遙測。
  • truck : n 1 〈美國〉運貨汽車，卡車；貨車 （＝ 〈英國〉 lorry）。2 （鐵路上的）手搖車；手推車，（車站上的...
  1. Passenger car, truck, bus and motorcycle tyres - methods of measuring rolling resistance

    乘用車卡車公共汽車和摩托車輪胎.滾動阻力測量方法
  2. Measuring engine transient process data in ca1258p1k2l11t1 truck in accelerated mode, recording and analyzing the data, then analysis the test error. 4. building model and simulating two typical running mode ? fixed 6th gear acceleration with initial vehicle speed 40km / h and gear change acceleration starting with 2nd gear, comparing calculated result with test result, revising transient process simulation model and analyzing error between calculation

    本文基於ca1258p1k2l11t1載重卡車對ca6df2 - 26發動機的瞬變工況進行試驗和模擬計算，結果表明: 1 ） gt - power軟體可以很好的模擬、分析、預測發動機瞬變過程，模擬計算的結果與試驗結果很接近，試驗證明，預測分析指出的改進方向是正確的; 2 ）加裝電動增壓器可以降低整車使用油耗，改善低速煙度排放，縮短加速時間，改善整車的加速響應; 3 ） gt - power軟體預測分析配合發動機和整車試驗是分析、解決發動機瞬變過程的有力工具。
  3. Test method of measuring rolling circumference for truck tyres

    載重汽車輪胎滾動周長試驗方法
  4. The division operates a portfolio of warehouses, logistics centres and port facilities measuring more than 16 million square feet backed by a truck fleet of over 3, 000 vehicles, with operations stretching across over 150 cities in 18 countries and supported by around 6, 000 staff in total

    部門目前營運面積逾1 ， 600萬平方尺的貨倉物流中心及港口等物流設施，以及一隊超過3 ， 000輛貨車的車隊，業務遍及18個國家及超過150多個城市，員工團隊約共6 ， 000人。
  5. Firstly the thesis expatiates the basic concept of reverse engineering, analyzes the basic principle of reverse engineering, the technology & theory of three dimensional measuring and basic theory of building 3 - dimensional free - form surfaces model. secondly it introduces the smooth methods of the free - form surfaces of auto body and solves point - data and surface reconstruction. finally the thesis expatiates applications and technology of auto body of futian heavy truck through reverse engineering

    本文首先將闡述逆向工程的基本概念，分析車身逆向工程的基本原理以及車身逆向工程中三坐標測量技術與原理，車身表面三維數學曲面模型建立的理論基礎，其次介紹車身外形曲面光順方法，以及車身逆向工程中點數據處理技術及曲線曲面重建技術，最後結合福田重卡車身逆向開發，重點闡述車身逆向工程技術的應用與流程。
  6. The microcomputer - controlled measuring control system for the diesel engine of electric - wheel truck

    電動輪汽車柴油發動機微機測控系統
  7. Application of atos scanner in measuring cab coverings of truck cab

    掃描儀在貨車駕駛室覆蓋件測量中的應用
分享友人
分享到 Line

分享到臉書