melt composition 中文意思是什麼

melt composition 解釋
熔體成分
  • melt : vi （melted; melted molten）1 融化；熔化；液解。2 逐漸消散[消失、變淡]。3 （心等）變軟，生憐憫的...
  • composition : n 1 作文（法），作詩（法），作曲（法）；作品，文章；樂曲；文體，措辭。2 編制；結構，構造，組成，...
  1. In this investigation carbon black - filled electrical conductive composites of poly ( ethylene terephthalate ) / polyethylene were first prepared through the single - screw melt - blended extrusion, then drawing, followed by the quenching and subsequent press molding. the relationships among the influencing factors including composition, hot stretching ratio and compatibilizer, morphology and properties of composites were systematically investigated. positive temperature coefficients effect and crystallization behaviors of composites were preliminarily analyzed

    本文擬採用單螺桿熔融共混擠出?熱拉伸?淬冷的新的成型方法制備炭黑填充的pet pe復合導電材料，熱拉伸的目的是使材料的分散相（ pet相）在加工過程中原位形成纖維，而炭黑基本分散在纖維中或纖維的表面上，使炭黑粒子間間距減小，形成更多的導電通路，從而提高材料的導電性能，同時保持或提高材料的力學性能。
  2. Examine the warm triangular awl composition and adopt mineral raw materials to compound, its physics performance and ceramic glaze medicine are self - same, utilize fire - resistant degree of it as melt temperature of pouring, in cooking, set according to the operation instructions free in examined warmly position in products, can examine to the actual temperature of the products ( can be observed with the naked eye ), especially push away and pull the kiln, tunnel kiln, drawer kiln observe temperature must spend products, general difference in temperature 5 - 10 degrees centigrade, please and soften some forms of contrasting according to the operation instructions, serial number before using

    測溫三角錐成分採用礦物原料配製的，它的物理性能與陶瓷釉藥完全相同，利用它的耐火度作為熔倒溫度，在產品燒成中，按使用說明放在所測溫的位置，可測到產品的實際溫度（用肉眼可觀察到） ，尤其是推扳窯、隧道窯，抽屜窯內觀察溫度必用產品，一般溫差5 10 ，使用前請按使用說明、編號及軟化點對照表。
  3. Effect of additional alloy composition on aluminum alloy directed melt oxidation growth

    補加合金成分對鋁合金熔體直接氧化生長的影響
  4. In attempt to prepare and study the novel electrically conductive nanocomposites, with polyethylene ( pe ) served as the matrix, maleic anhydride grafted polyethylene ( gpe ) served as eg intercalates and expanded graphite ( eg ) served as a conductive filler, prepared gpe / eg, pe / gpe / eg electrically conductive composites via solution intercalation ( si ), direct melt mixing ( dmm ) and master batch melt mixing ( mmm ) methods. by means of testing conductivity and mechanical property, with the measures of tem, sem, om, xrd and dsc, studied the relationship between preparation method, material composition, and electrically conductive as well as mechanical property. the main outcomes never reported at home and abroad literature were obtained as follows : 1 the gpe / eg electrically conductive nanocomposites were prepared via si method

    本論文以制備和研究新型高分子導電納米復合材料為目的，以聚乙烯（ pe ）為基體，馬來酸酐接枝聚乙烯（ gpe ）為插層劑，膨脹石墨（ eg ）為導電填料，採用溶液插層（ si ）法、直接熔體混合（ dmm ）法和兩者相結合的熔體母料混合（ mmm ）法制備了gpe eg 、 pe gpe eg導電復合材料，通過電導率和力學性能測試，運用tem 、 sem 、 om 、 xrd和dsc等手段，研究了制備方法、材料組成、形態結構和導電性能及力學性能之間的關系，得到以下未見國內外文獻報道的研究結果： 1採用si法成功制備了gpe eg導電納米復合材料，其導電逾滲閥值（ _ c ）為1 . 59vol ，遠低於dmm法制得gpe eg常規復合材料的_ c （ 3 . 13vol ） 。
  5. The film index is higher than that of bulk glass of the same composition as the target, but prepared by rapid quenching from the melt.

    薄膜折射率高於與靶成分相同的體型玻璃折射率，而此玻璃是由熔體迅速冷卻制得的。
分享友人
分享到 Line

分享到臉書