melt extrusion 中文意思是什麼

melt extrusion 解釋
熔融擠出
  • melt : vi （melted; melted molten）1 融化；熔化；液解。2 逐漸消散[消失、變淡]。3 （心等）變軟，生憐憫的...
  • extrusion : n. 1. 擠壓，擠壓成形；擠出。2. 逐出。3. 【地質學；地理學】（熔巖的）噴出；突出，伸出。
  1. Calculatie retention time of plastic melt in extrusion moulding head

    塑料熔體在擠出模頭中停留時間的計算
  2. Standard test method for melt flow rates of thermoplastics by extrusion plastometer

    使用擠壓式塑性計測定熱塑塑料的熔融流量率的標準試驗方法
  3. In this investigation carbon black - filled electrical conductive composites of poly ( ethylene terephthalate ) / polyethylene were first prepared through the single - screw melt - blended extrusion, then drawing, followed by the quenching and subsequent press molding. the relationships among the influencing factors including composition, hot stretching ratio and compatibilizer, morphology and properties of composites were systematically investigated. positive temperature coefficients effect and crystallization behaviors of composites were preliminarily analyzed

    本文擬採用單螺桿熔融共混擠出?熱拉伸?淬冷的新的成型方法制備炭黑填充的pet pe復合導電材料，熱拉伸的目的是使材料的分散相（ pet相）在加工過程中原位形成纖維，而炭黑基本分散在纖維中或纖維的表面上，使炭黑粒子間間距減小，形成更多的導電通路，從而提高材料的導電性能，同時保持或提高材料的力學性能。
  4. Numerical simulation of three dimensiona isothermal power - law polymer melt flow within an extrusion die with the quot; l quot; shaped cross section

    型異型材擠出口模內聚合物熔體三維等溫冪律流動的數值模擬
  5. Numerical simulation and analysis of polymer melt filling flow driven by a periodically oscillating entrance pressure through the extrusion die with an irregular cross - section

    振動場作用下聚合物熔體在異型材擠出口模內的充填流動分析
  6. Based on theory of gear driving, fluid mechanics, hydrodynamic lubrication, polymer rheology and single - screw extrusion, key structure design principles in melt pump are summarized, some theory foundations are also deduced

    結合齒輪傳動、動力潤滑、流體力學、高聚物加工流變學以及單螺桿擠出理論的部分知識對熔體泵結構設計中的主要問題進行了總結，並對其中部分理論依據進行了推導。
  7. Melt grafting modification of polypropylene by reactive extrusion

    利用反應擠出的聚丙烯熔融接枝改性
  8. Large extrusion output, low and equal melt temperature

    擠出量大，熔體溫度低，熔體溫度均勻。
  9. Thanks the solution to accurate controlling and compelte stabilizing of the extrusion process by employing the melt measuring gear pump

    基於在塑料擠出行業中多年積累的實際經驗，精誠模具為解決這些問題，採用融體計量齒輪泵，使系統得到準確的控制和擠出過程中的完全穩定。
  10. Studies on preparation of pa6 - 66 montmorillonite nano - scale composite by melt extrusion

    蒙脫土納米復合材料的研究
分享友人
分享到 Line

分享到臉書