melt phase 中文意思是什麼
melt phase
解釋
熔融相-
The dendrite growth in the undercooled melt of pure has been simulated by the phase - field method
摘要簡介了相場方法，利用相場法對純鋁進行了數值模擬。 -
Adopt advanced technic of f4 whole cold - press to moulding and heat melt to process to make, let the lining no slot to link withal cheek by jowl connect with exterior metalpipes wall, in the state of allowwing to work keep to distort in - phase, thereby to enhance using - life of lining in the working status of opposite high temperature high vacuum, stop the ecumenic pad fluorin pipes using in condition of cold and heat alternate and minus tension to come into being the matter of padding fluorin floor shrivel to jam the flowway and plastic rip, its perfect choice use to transport medium of strong corrosive strong oxidation by modern chemical - industry corporation
採用氟塑料f4整體冷壓成型及熱熔加工等先進技術製造，使內襯層無縫搭接且與外層金屬管壁緊密粘接，在允許工作狀態下能夠保持同步變形，從而提高了襯里層在相對高溫高真空度的工況下的使用壽命，杜絕了一般襯氟管在冷熱交替，及負壓的條件下使用易產生襯塑層鼓癟阻塞流道及塑料拉裂的問題，是現代化工企業在輸送強腐蝕強氧化介質理想的選擇。 -
Rainfall is started mainly in cold portions. microphysics for ground rainfall consists of low - level warm portions in which precipitating particles are produced, growing through collision with cloud water and when descending into the warm portions below, ice - phase particles melt and continue to grow by collecting cloud water there. 4 )
降水主要以冷雨過程發動，地面降水形成的微物理過程分別為低層暖雲過程產生並通過碰並雲水增長、降落到暖區的冰相粒子融化和融化的冰相粒子在雲的暖區收集雲水繼續長大等三部分組成。 -
Abstract : design ideas, technical features and system architectures of advanced process control for polypropelene units were introduced together wit h on - line calculations for the controlled variables such as the yield of polypr opelene, concentration of monomer, hydrogen concentration in liquid phase and the melt flow rate index. attentions in implementation were pointed out
文摘:介紹聚丙烯裝置先進控制技術的設計思想、技術特點和系統構成，並介紹產率、漿液濃度、液相氫氣濃度、熔體流動指數等被控變量的在線計算，指出了實施中應注意的問題。 -
The result of experiment showed that the reaction between ti and c is a thermodynamic course, when 2 wt % mg is added to melt, it can restrain the formation of fragility phase al3ti, and gained al matrix composite which contained tic reinforced particles only. because mg reacts with the forms a micro - high temperature field around the oxide around the graphite particles and the oxygen gas which is brought by the immersion bell, and the reaction gives out a lot of heat energy, thus forms many high micro - fields in melt, which prompt the reaction between the al and ti
加入適量的mg （ 2wt ）可以抑制tic al復合材料中的脆性相al _ 3ti的產生，生成僅含tic的鋁基復合材料；由於活化劑鎂在體系中與石墨顆粒周圍的氧化物、以及外來的氧反應放熱，在熔體中形成微高溫區，促進al - ti反應，同時， al - ti反應也是放熱反應，因此體系中的內能急劇增大，促使al _ 3ti分解以及ti朝c顆粒擴散，縮短反應的孕育時間。 -
Chlorine tends to be partitioned into the fluid phase while fluorine shows a strong tendency to the melt phase. df increases ; with the fluorine content increasing, and so does the dcl
Cl在流體?花崗質熔體相間的配分系數均大於1 . 0 ，且d _ （ cl ）隨體系中cl濃度的升高而增大， cl強烈地趨向富集於流體相中。 -
Through the study, the phase change materials on residential storing energy was obtained whose melt point is 16 - 28 c and heat of transformation reach or exceed 180j / g
通過研究確定出可用於建築節能的相變貯能材料，其相變點在16 28 ，相變熱達到或超過180j g 。 -
Double - shell heat energy storage microcapsule was prepared used the prosperities of microcapsules were investigated. a phase change material as core, which melt point was 24 c and phase transition heat was 225. 5j / g. the microcapsules would been used in indoor wall to regulate the temperature and saving energy sources. the surface morphological structure was examined by means of scanning electron microscopy
其中當乳化速度為2500r min 、乳化時間大於5min 、壁材滴加速度小於0 . 5ml ? min ~ （ - 1 ）且系統調節劑為芯材的30 40時微膠囊的粒徑分佈集中； dsc顯示微膠囊包覆相變材料不影響其相變點，相變儲熱明顯。 -
On the base of the study, a new preparation technique of al2o3 / sic / ni / al - si multi - phase ceramic matrix composites was developed by oxidative infiltration of al - 5zn - 10si alloy melt into sic / ni performs made by slip casting at high temperature
在此基礎上，發展了一種採用注漿成型法制備sic ni預制體，通過al - 5zn - 10si合金在高溫下滲透氧化法制備al _ 2o _ 3 sic ni al - si合金多相陶瓷基復合材料的新技術。 -
Moreover, rare earth ceo2 can clean the melt and the face of reinforced particles and improve the wettability between the reinforced phase and melt and the property of material. proper additive mg and rare earth can improve the hardness, wear - resisting property tensile - strength, elongation percentage of tic / al, tic / al - si composite
加入適量添加劑mg和稀土ceo _ 2使原位tic al ， tic al - si復合材料的硬武漢科技人學碩1 ：論義度、咐磨性、抗拉強度、延伸率得到很大的提高。 -
Phase separation ( nonsolvent induced phase separation, spreading solution on water surface and so on ), melt stretch, thermally induced phase separation are included
重點介紹了聚4 -甲基1 -戊烯微孔膜各種制備方法的原理、過程、影響因素和膜的結構特點。
分享友人