member in bending 中文意思是什麼
member in bending
解釋
受彎構件-
The author studies the calculation of steel in reinforcement conc rete bending member with round section
這種計算方法會造成鋼材的較大浪費。 -
Here the hsc of sompa is achieved through adding super - effective water reducer, fined slag and silicon fume, and decreasing the water / cement ratio. by varying the area ( spacing ) of tension bars, compressive bars, vertical links and distribution steel and embedding steel fiber and polypropylene fiber we try to improve the behaviors of reinforced high performance concrete one - way spanning slabs in bending, so that its ductility be greater than 5. with the same arrangement of steel the width of bending member is varied to observe the effect of the width / depth ratio on the ultimate compressive strain of concrete
通過變化受拉筋含筋率和受壓筋、箍筋（鉤筋、分佈筋）含量，或摻加纖維使之成為鋼纖維高強混凝土（ sfrhsc ）和聚丙烯纖維高強混凝土（ pfrhsc ） ，對高強混凝土雙筋截面梁、板的受彎性能進行了試驗研究，試圖改善高強混凝土受彎構件的延性，使其延性比大於5 ；並在相同配筋情況下，通過變化截面寬度，研究了高強混凝土受彎構件的寬高比對壓區混凝土極限應變的影響；並對試驗構件的裂縫發展情況進行了觀測。 -
Lastly, the minimum permission reliability index is offered by the method of " calibration method " which makes back calculation out of the bending resistance reliability and the compression resistance reliability of the reinforced concrete member in norm
最後，根據「校準法」反演計算現行設計規范中鋼筋混凝土結構抗彎、抗壓可靠度指標以確定在用橋梁結構體系的最低目標可靠度指標。 -
Finally, a correlative equation about bearing capacity of this structural member under bending and torsion is deduced, which may provide design of such structural members a valuable reference. to imitate centrifugal concrete - filled steel tubes used in real structures, three - dimension models are built up by using finite element method. the resistance performance of this structure under complex loads is studied
利用三維有限元模擬分析方法對離心鋼管混凝土在彎扭組合作用、彎壓組合作用、壓扭組合作用下的構件彈性應力分佈進行了研究，分析了離心鋼管混凝土構件在組合作用下的工作機理和承載力的相關關系。 -
In this part, it is also found that the equivalent prismatic column, which is obtained based on the equal elastic critical load as the non - prismatic member, is not actually equivalent to the tapered column in inelastic stability, and the latter has higher load carrying capacity. finally, the behavior of tapered beam - column acted by combined axial load and transverse load has been investigated. a bending - thrust interaction curve is established which is similar to the ones for the design of prismatic members
三是研究了楔形變截面懸臂構件在大端固定，小端同時承受橫向及軸向荷載共同作用下的強度和彎矩平面內的穩定，同時參考等截面構件的設計公式，得到了用大端截面來表示的軸力p與彎矩m的之間的相關關系。 -
Simple methods of calculating the section area of the vertically - pulled steel in the bending member on the rectangle section of steel concrete
鋼筋混凝土矩形截面受彎構件縱向受拉鋼筋截面面積的簡便計算方法 -
2. for frame supported double - short - pier shear wall under vertical loads, the non - noding area of transfer beams turns into a member of flexure and tension with small axial force, and bending stress dominates in the stress distribution on the cross - section. in the nodding area, the axial force increases while the bending effect is small
2 、框支雙肢短肢剪力墻在豎向荷載作用下，轉換梁的非節點區為一拉彎構件，軸向拉力較小，截面的應力分佈以彎曲應力為主;在節點區，軸向拉力效應增大，而彎曲效應很小。
分享友人