member in shear 中文意思是什麼
member in shear
解釋
受剪構件-
6. the sectional cross - sectional discrete yield - sruface model is used to spandrel deep beams, the effect of the shear deformation to shear force on ( he m ~ terial nonlinearity is considered, ( he bond slip in anchorage zones is regarded as the houndaty nonlinearity of a member. except the geometric nonhineaicty. consideration of double nonlinearities about materials an
6 、將分段截面離散的屈服面模型法應用於裙梁，考慮剪力剪切變形對材料非線性的影響，將錨固區鋼筋的粘結滑移看成構件的邊界非線性，不考慮幾何非線件，建立了裙梁考慮村料、邊界雙重非線性的空間滯回曲線分析模型。 -
The lower member of typical ophiolite suit is exposed at outsides of the qimanyuter ophiolite melange and in between, there distribute the basalt, deep sea limestone and silicalites. these different litho - members contact to each other with ductile shear zones
帶內蛇綠巖套下部單元出露于兩側，玄武巖和相關的深水灰巖、硅質巖等分佈於中部，各單元間均以韌性剪切帶接觸。 -
Firstly, the shear and normal stresses of tapered members under the transverse load or axial load are analysed, and the stresses formulas are obtained which are different from those of the prismatic ones. secondly, research is done on the in - plane inelastic stability of tapered members under axial loads about strong axis and weak axis. a new design method is suggested in which the tapered member is equivalent to the prismatic member with the cross - section at the larger end of the tapered member
同時由分析可知，目前採用的將變截面壓桿按照彈性極限荷載等效的原則等效成以小端截面為準的等截面壓桿的設計方法，在彈塑性階段低估了壓桿的承載力，即彈性等效的壓桿在彈塑性階段並不等效，實際變截面壓桿的承載力比等效的等截面壓桿的承載力要高。 -
Then calculate the member individually, including the calculation of load - behavior capacity, the calculation of high strong bolt with the method of connection with beam, the design method of stiffening rib, etc. the text educed the above - mentioned formula theoretically. 5. linking with windmill flat engineering example in the third youth flat engineering of yi zhuang development area, beijing, it and steel frame constitute the steel frame ? steel shear wall with slit system respectively are analyzed the whole structure by ansys and satwe
既利用剛度等效的原則，把其轉換為工程計算軟體可以計算的支撐體系，然後對構件進行單獨計算，包括承載力的計算、和梁接合方法? ?高強螺栓的計算、加強肋的設計方法等內容； 5 、帶縫鋼板剪力墻與鋼框架形成鋼框架? ?帶縫鋼板剪力墻結構體系，結合北京亦莊經濟開發區青年公寓三期工程中的風車公寓工程實例，分別採用ansys和satwe進行了結構整體分析，兩者的計算結果相吻合。 -
Although two simple models of structural analysis models, namely multi - storey shear type and member model, are set up, it is proved that simulink show great dominance in simulation of structural dynamic response, especially in vibration control
本文所做的工作雖然僅實現了結構分析模型中較簡單層間模型和平面桿系單分量模型的非線性地震反應模擬，但已足以體現出simulink用於結構動力模擬和結構振動控制的優越性。 -
The project is completed in the collaboration of the transportation college of jilin university and transportation science institute in jilin province. the paper mainly studies the characteristics and mechanical performance of small size member of bridge, the problems of concrete dense degree and shear lag effect of wide flange. the static load test and supersonic nondestructive test of four pieces of prestressed i - girder with varying section are carried out in bridge structure laboratory of jilin university
本文針對橋梁構件局部尺寸較小部位的混凝土密實度問題，進行了2片腹板寬度為14cm ， 2片腹板寬度為16cm的變截面預應力工字梁的靜載試驗和超聲無損檢測試驗，提出密實度系數的概念，對試驗梁的密實度進行定量評定，推導了工字梁的塑性系數公式，基於塑性理論給出了試驗梁的開裂荷載和極限承載能力計算公式，分析了試驗梁的密實度對其開裂荷載和極限承載能力的影響。 -
2. for frame supported double - short - pier shear wall under vertical loads, the non - noding area of transfer beams turns into a member of flexure and tension with small axial force, and bending stress dominates in the stress distribution on the cross - section. in the nodding area, the axial force increases while the bending effect is small
2 、框支雙肢短肢剪力墻在豎向荷載作用下，轉換梁的非節點區為一拉彎構件，軸向拉力較小，截面的應力分佈以彎曲應力為主;在節點區，軸向拉力效應增大，而彎曲效應很小。
分享友人