meshing point 中文意思是什麼
meshing point
解釋
嚙合點-
As both the meshing point and ball ' s center are on the given cylinder, a general method for developing the cam ' s profile is studied. it is proved that the profile of positive and negative transmission is unique if the face gear, the difference between face tooth number and ball number and the diameter of ball are the same. the concrete expression of meshing cam on given spatial cycloid profile, and the characteristics of the profiles are discussed
論文的主要工作包括： 1 、根據嚙合點和鋼球中心軌跡均在同一圓柱面上的特點，研究了給定端齒齒廓條件下求解凸輪齒廓的一般方法；論證了在給定端齒、齒差數和鋼球直徑相同的條件下，正負齒差嚙合齒廓的唯一性；討論了端齒為球面擺線時，凸輪齒廓的具體表達式，並研究了該齒廓的性質。 -
Equations of mesh, shorting contact line, undercutting limit line, meshing limit lines and the existence conditions, angle between the direction of relative speed and the direction of contact line, induced normal curvature about every point on the contact line are established. moreover, the paper also theoretically analyzed the error of the grinded gear surface. on the basis of the theory, the computer program is worked out to automatically produce the contact line and the boundary curves of mesh. analysis of meshing circs under different parameters can be done so that we can gain the best process condition
首先對漸開面二次包絡理論進行了深入的探討，推導出了兩次嚙合的嚙合方程式、瞬時接觸線方程式、根切界限線方程式、嚙合界限線的方程式及其存在條件，相對運動速度方向與接觸線方向的夾角及接觸線上各點的誘導法曲率；此外，還對磨齒后工件的齒面誤差進行了理論分析；並在理論基礎上編制了相應的計算機程序，自動生成接觸線族及嚙合界限線，對不同參數條件下的嚙合情況進行分析，可以使工藝條件達到最佳狀態；最後研究了磨齒裝置，設計了磨齒機的傳動系統。 -
Dqj point - line meshing gear reducers
Dqj點線嚙合齒輪減速器 -
Gear form is precisely, plotted by portray point. for friendly user interface, the dialog - box is given, using dcl language to compile dialog box program. because the given program can not only output all the optimum basic parameters of pump gear, but also simulate the meshing process of a pair of pump gears, gear pump can be designed and manufactured economically
精確繪出泵齒輪的輪齒幾何形狀，尤其精確繪制出了標準齒輪滾刀切出的齒根過渡曲線，演示了國標雙圓弧頭標準滾刀加工泵齒輪的過程，並實現了泵齒輪副的嚙合模擬，這些對檢查輪齒干涉以及確定齒輪泵的卸荷槽位置和形狀提供了依據。 -
The curvature interference of the gear and the influence of radius of the mill - cutter, axial misalignment, and center distance on meshing are analyzed. based on these analyses, propose two methods to achieve point - contact : to change the radius of the mill - cutter and increase the center distance
在分析了弧齒線圓柱齒輪的嚙合傳動不產生曲率干涉的條件和刀盤展成半徑、軸線平行度誤差、中心距對嚙合影響的基礎上，提出了點接觸弧齒線圓柱齒輪實現的兩種方案:調整刀盤展成半徑和增大中心距。 -
Some numerical technicalities, such as choice of fundamental solution to governing equation of flow problem, treatment process to corner point problems, automatic meshing, treatment process for fractures partly beyond the flow domain boundaries, were also discussed. thirdly, a hybrid bem - channel model was presented, and the numerical procedure for which was described
進行了裂隙巖體的多孔介質水力等效性分析，研究了裂隙巖體的滲透系數的張量形式，闡述了裂隙巖體等效水力性質的計算方法，包括rev大小的估計和等效滲透系數張量的計算。 -
Design and research on double - track transmission device under multi - point gear - meshing flexibility
雙軌道型多柔傳動裝置的設計研究
分享友人