metal-to-metal 中文意思是什麼

metal-to-metal 解釋
金屬對金屬的
  • metal : n 1 金屬；金屬製品；金屬合金。2 【化學】金屬元素；（opp alloy）；金屬性。3 【徽章】金色；銀色。4 ...
  • to : adv 到某種狀態；〈特指〉到停止狀態；關閉。 ★也常和動詞結合，略去其後賓語，而構成成語： The door i...
  1. Fire safe ? secondary metal - to - metal seal acts as backup if primary seal is destroyed by fire. valves ordered for compliance with api 607 will be provided with graphite packing and gaskets

    氯氣應用-可提供能夠滿足氯氣協會第6小冊子所列的全部標準和規定的閥門，包括通風球的預備，流向箭頭，以及為了防止污染而進行的清洗和包裝。
  2. Metal - to - metal seating means not best choice for frequent operation. bubble - tight seating should not be expected with metal - to - metal design

    金屬對金屬閥座意味著不適用於頻繁操作。金屬對金屬結構也不適用於無氣泡閥座。
  3. Circular sight glasses with case in metal to metal contact type flanged joint

    金屬與金屬接觸式法蘭連接中的有罩圓形觀察孔
  4. The method of creep properties of adhesive in shear by tension loading metal to metal

    膠粘劑拉伸剪切蠕變性能試驗方法
  5. For the valve with the metal to metal seal, there is grease injector outside of it, grease gets into the sealing face through the injector and the seat ring to have the valve up to null leak

    金屬對金屬密封的閥門，閥體外部設有注油脂結構，油脂通過注脂器、閥座進入閥門密封面，使閥門達到零泄漏。
  6. B connections for general use and fluid power - ports and stud ends with iso 261 threads with elastomeric or metal - to - metal sealing - stud ends with metal - to - metal sealing type b

    普通和液壓用聯接結件.用iso 261螺紋的彈性或金屬與金屬間密封的氣門和雙頭螺栓端頭
  7. Standard test method for cleavage strength of metal - to - metal adhesive bonds

    金屬之間膠粘劑粘結力抗裂強度的標準測試方法
  8. Standard test method for creep properties of adhesives in shear by tension loading metal - to - metal

    用拉力負荷法測定金屬之間膠粘劑蠕變性能的標準試驗方法
  9. Test method for strength properties of adhesives in shear by tension loading at elevated temperatures metal - to - metal

    高溫下用拉力負荷法測定金屬之間膠粘劑剪切強度的試驗方法
  10. Standard test method for apparent shear strength of single - lap - joint adhesively bonded metal specimens by tension loading metal - to - metal

    用拉力負載法測定單面搭接粘結的金屬試樣表面剪切強度的標準試驗方法
  11. Standard test method for creep properties of adhesives in shear by compression loading metal - to - metal

    用壓力荷載法測定金屬之間膠粘劑蠕變性能的標準試驗方法
  12. Standard practice for conducting creep tests of metal - to - metal adhesives

    進行金屬間膠粘劑蠕變試驗的標準實施規程
  13. Gate and globe ( metal to metal ) seats cannot provide bubble tight shut - off. resilient seated butterfly valves are bubble tight by design

    閘閥和截止閥（金屬與金屬連接）的閥座不具備不透氣關閉的性能。
  14. This will ensure good metal - to - metal contact and minimum leakage

    這將保證有良好的金屬-對-金屬接觸面和最小的泄漏。
  15. Connections for general use and fluid power - ports and stud ends with iso 261 threads with elastomeric or metal - to - metal sealing - threaded ports

    普通和液壓傳動用聯接件.用iso 261彈性螺紋或金屬與金屬間密封的氣門和雙頭螺栓端頭.螺紋氣門
  16. E connections for general use and fluid power - ports and stud ends with iso 261 threads with elastomeric or metal - to - metal sealing - stud ends with elastomeric sealing type e

    普通和液壓傳動用聯接件.用iso 261彈性螺紋或金屬與金屬間密封的氣門和雙頭螺栓端頭
  17. Connections for general use and fluid power - ports and stud ends with iso 261 threads with elastomeric or metal - to - metal sealing - part 1 : threaded ports

    一般用途和流體動力用連接件.帶彈性體密封件或金屬對金屬密封件的iso 261螺紋的孔口和螺柱端.第1部分:帶螺紋的孔口
  18. Connections for general use and fluid power - ports and stud ends with iso 261 threads with elastomeric or metal - to - metal sealing - part 2 : stud ends with elastomeric sealing type e

    流體動力用和通用連接件.帶iso 261螺紋，帶有彈性體或金屬對金屬密封件的埠和螺柱斷頭.第2部分:帶彈性密封的螺柱端頭
  19. Connections for general use and fluid power - ports and stud ends with iso 261 threads with elastomeric or metal - to - metal sealing - part 3 : stud ends with metal - to - metal sealing type b

    一般用途和流體動力用連接件.帶彈性體密封件或金屬對金屬密封件的iso 261螺紋的孔口和螺柱端.第3部分:帶金屬對金屬密封件的螺柱端b型
  20. B connections for general use and fluid power - ports and stud ends with thread - stud ends with metal - to - metal sealing type b

    液壓管接頭用螺紋油口和柱端金屬對金屬密封柱端
分享友人
分享到 Line

分享到臉書