meter paper 中文意思是什麼

meter paper 解釋
儀表用紙
  • meter : n. 1. 測量儀表，計量器；計，表。2. 計量人；計量官。vt. 用表計算[測量、記錄]。n. 〈美國〉＝ metre.
  • paper : n 1 紙；裱墻紙。2 報紙，報。3 收據；債券；證券；票據；匯票；鈔票（＝paper money）。4 〈pl 〉身份...
  1. This paper discusses the designing and making of the dynamic testing systems of engine electronic control system. base on the construction and operation principle of santana 2000gsi m3. 8. 2 engine electronic control systems, design and manufacture led circuit of dynamic testing and fault imitating electronic control unit. on the inspect board, design and equip with motronic 3. 8. 2 ecu i / o measuring joints, design and set up obd - ii diagnostic communication link, design and install fuel pressure inspecting meter. depend on the obd - ii diagnostic communication link and ecu i / o measuring joints, this dynamic testing system can inspect engine electronic fuel injection system, distributorless ignition system, idle speed control system and evaporative emission control system, and can inspect m3. 8. 2 sensors, ecu and actuators, and can interrogate fault memory and erase fault memory ; and can analyse data stream ; and can carry out fault imitating. besides, this paper analyses sensors and actuators typical fault w aves

    2電控單元電路連接器設計製成輸入輸出電子控制檢測端子，並在檢測面板上布置了obd -診斷插座和燃油壓力表。使該動態測試系統能實現對電噴發動機的燃油系統、直接點火系統、怠速控制系統和燃油蒸氣排放控制系統的動態檢測；並通過obd -診斷座、 ecu輸入輸出檢測端子和故障模擬處理單元實現對電噴發動機電控系統各傳感器、電控單元、執行器進行故障碼讀取與清除；動態數據讀取和波形測試和故障模擬等。此外，本論文還分析了傳感器和執行器典型故障波形。
  2. Bosch filter paper smoke meter

    濾紙測煙計
  3. Abstract : based on analysis of the operational principle of the traditional inductosyn digital display meter in the paper, the contradiction between detecting resolution ratio and antidisturbance ability is discovered. and then, to resolve the contradiction, the method of demodulation technology and high frequency excitement technology being used is advanced

    文摘:通過分析傳統鑒相型數顯表的工作原理，揭示了其檢測解析度與抗干擾能力之間的矛盾，並提出了採用差頻解調和高頻激磁等技術解決矛盾的方法。
  4. Label paper for postage meter

    郵資機簽條紙
  5. The intelligent inspect system for roof slts in shenzhen citizen center is selected as a practice engineering background in this paper, the structure is a new political and cultural center and a symbolic architecture in shenzhen which overall structural area is 2. 1 million square meter, the roof is the largest space lattice in the world which is 486 meter long and 154 meter wide

    本文以深圳市民中心為實際工程背景，深圳市民中心是深圳市新的政治文化中心和標志性建築。其總建築面積近21萬平方米，大屋頂空間網架結構長486米，寬154米，是迄今為止世界上最大的網架結構。
  6. In this paper, features of decadal variability and the possible mechanism of sea - air system in the pacific are investigated by using upper - ocean temperature, heat storage and wind stress data, the main results are as follows : the most pronounce decadal sign exists at about 160 meter in depth in the western pacific. there are significant decadal abrupt changes in temperature from surface to deep in the subsurface at about 1980. with different depth in the subsurface, there exist 4 types of abrupt change modes, their generation is closely related to the decadal sign which originates from the east of north pacific and propagates along the south - west subduct ion route

    研究表明，太平洋次表層海溫最強的年代際信號在熱帶西太平洋約160m深處，此信號在1980年前後從上至下，先後經歷了一次顯著的年代際突變過程，而且隨深度的不同存在著四種不同的空間突變模態，這四種模態的形成與北太平洋海溫異常的西南潛沉路徑有著密切的聯系。
  7. Optical power meter real - time monitor optical power of each optical cable, and control computer gather the value of optical power attenuation circularly, if some values excess the limit, the computer control optical switch to connect another spare optical fiber with otdr card, control the otdr card to test the optical fiber, and then find the malfunction point accurately. the system require software system to run with hardware devices tother. this paper analyze requirement and technical feasibility in software system, ooa and uml are used to analyze software and abstract the class diagram

    通過光功率計對每條光纜中的備用光纖進行實時的監控，測試光功率的衰減值，主控計算機不斷循環的對每個光功率模塊進行數據採集，並記錄每路光信號的光功率衰減值，然後進行分析處理，如發現達到設定的光功率衰減門限值就報警，並控制光開關的切換，將故障光纜中的另一備用光纖與otdr卡連接，通過otdr卡對該光纖進行測試，從而確定故障點。
  8. The system has advantages of carriable, easy to upgrade and expansive, etc. the paper studies the key technologies of development embedded system with the background of 3d laser distance meter system

    本文以三維激光測距系統為應用背景，深入研究了嵌入式系統開發過程中的關鍵技術並進行了實現。
  9. Traditional energy meter can cause errors under the condition of harmonics due to its structural characters, and at the same time harmonic loads take in foundational power and send out harmonic power. this paper proposes a new way and realizes accuracy and fair energy metering

    傳統的電能表在諧波存在下由於自身的結構特性會產生誤差，就此進行分析提出了新的電能計量方法，應用虛擬儀器技術實現了準確、公平、合理的電能計量。
  10. Abstract : in this paper, the design of the sense organ of the silicon miniature inertial meter is presented. the approving structure of the sense organ is fulfilled by the fabrication techniques of laser processing and chemical etching, laser fibre optic vibration is used to test the vibration characteristic of the suspensi on beams

    文摘:設計了硅微型慣性加速度計的敏感頭並應用激光加工和化學蝕刻相結合的工藝方法製造得到了滿意的結構，應用激光光纖測振儀檢測了懸臂梁振動特性。
  11. In this paper, the design of the sense organ of the silicon miniature inertial meter is presented. the approving structure of the sense organ is fulfilled by the fabrication techniques of laser processing and chemical etching, laser fibre optic vibration is used to test the vibration characteristic of the suspensi on beams

    設計了硅微型慣性加速度計的敏感頭並應用激光加工和化學蝕刻相結合的工藝方法製造得到了滿意的結構，應用激光光纖測振儀檢測了懸臂梁振動特性。
  12. This paper gives a comprehensive presentation about the fundamental of the flow - measuring method by flume, the design of khafagi flume and the buoy - level mechanism, the signal conversion by the angle measuring sensor and the deduce of the flow equation. it also introduces the hardware design, the development and emulation on software of the intelligent measuring meter in detail. the error of flow measurement is analyzed and calculated in the end either

    本文對槽式流量測量的基本原理、卡發基槽和浮桿測量機構的設計、角度傳感器的信號轉換以及流量計算公式的推導做了全面的闡述；詳細介紹了智能儀表應用系統的硬體電路設計和應用軟體的開發及模擬調試；最後對測量系統的各項誤差進行了分析和計算。
  13. Record paper for y311 yarn eveness meter

    Y311條粗條干儀用記錄紙
  14. We write the program which used for fighting errors in absolute positioning. we also write the program which used for linear combinating in absolute positioning. from analyzing for the measurement of outer, we can conclude that we can use m estimation to estimate parameter in gps absolute positioning. lt has application value. using it, we can obstain the stable positioning result and remove the outer. in this paper, we calculate the data which from the baseline space of the gps calibration space. we also draw some conclusion using broadcast ephemeredes and smoothing pseudoranges. the positionging precision is in 1 - 2 meter

    編制了gps絕對定位中抗差估計程序和應用線性組合進行單點定位的程序。通過對粗差量級的分析，得出在gps觀測量存在粗差時， m估計是有其應用價值的，它使定位結果較為穩定，減弱和剔除了粗差的影響。應用線性組合程序對gps綜合檢定場數據基線網點進行計算，得出用廣播星歷和平滑后的偽距可以給出較好的結果，點位精度在1 ? 2米。
  15. In the paper the effects of the made parameters, the main materials and environmental conditions on plastic shrinkage cracking were investigated. it can be concluded as following : 1 ) there was a critical w / c ratio of maximum plastic shrinkage cracking between lower and higher w / c ratio of concrete mixtures made with the same cement content per cubic meter, concretes with lower or higher w / c ratio being less prone to plastic shrinkage cracking and the w / c critical ratio critical of maximum plastic shrinkage cracking being about 0. 5

    本文研究了配製參數、主要原材料以及環境條件對新拌混凝土塑性收縮裂縫的影響，結果表明： 1 ）單方混凝土水泥用量一定時，較低水灰比和較高水灰比對應的混凝土拌合物不易開裂，而中間某一臨界水灰比對應的混凝土拌合物開裂較嚴重，這一臨界水灰比為0 . 5 ；單方混凝土水用量或水泥漿量一定時，混凝土拌合物的塑性開裂趨勢與上述情況相似，但臨界水灰比分別為0 . 45 - 0 . 4和0 . 4 。
  16. This paper, after discussing the basic theory and the application of digital image processing and analyzing the concrete characteristics of the water meter, puts forward the crux algorithm that identifies automatically the position and direction of the pointers of water meter with techniques of the image preprocessing, image segmentation and image analysis and recognition

    本文結合水表的具體特點，分析了將圖像處理技術應用於自動識別水表指示讀數的原理。找到了一種滿足一定速度和精度的水表讀數識別方法。該方法主要包括水表圖像預處理、水表圖像分割、指針讀數的識別。
  17. The influence of nano - al2o3 on the sintering and the properties of the si3n4 ceramics was researched in this paper. the samples with different amount of nano - al2o3 were obtained by using pressureless sintering at 1600, 1650, 1700 in the nitrogen atmosphere. the microstructure and the composition of the ceramics were determined by the means of x - ray, sem, micro - hardness meter etc. it is show that the sisty ceramics can be densified at 1650c to % percent of the theory density through the addition of nano - al2o3 ( the value could be 90 percent by other technique ). the crystalline growth of the cylindrical - si3n4 and the ratio of its longitude to its diameter are increased with the addition of nano - al2o3. a uniform microstructure and an fined crystal as well as more sialon phases can be obtained in the si3n4 ceramics through the addition of that

    實驗結果表明：在碳管爐中、氮氣保護下進行燒結，添加劑為納米al _ 2o _ 3粉末時，由於納米粉末的高活性、高燒結驅動力，在1650就可使si _ 3n _ 4完全地燒結，並使其緻密度可達理論密度的96以上（比其它工藝高6左右） ；同時，納米al _ 2o _ 3地加入大大促進了長柱狀? si _ 3n _ 4的生長和發育及柱狀晶長徑比的提高，使微觀結構均勻、細化，形成了更多力學性能優異的固體? sialon相，減少了不利於陶瓷材料性能的晶間玻璃相，凈化了晶界。
  18. In this paper, the application of dsp technology in electric power measurement meter has been studied, meanwhile analysed the error of the electronic energy meter, put forward the measure to compensate error with software method. it not only changes the precision degree of electric power measurement meter, but also avoids the disadvantage from error compensate with hardware method, it is unnecessary to adjust the sample value of voltage and electric current in circuitry

    對dsp技術在電度表中的應用進行了研究，對電度表系統的誤差進行了分析，提出了採用軟體方法來補償誤差的措施，使電度表的精度達到了設計要求，又避免了利用硬體進行誤差補償所帶來的弊端，不用在線路中調整電壓、電流采樣值，有利於生產。
  19. The history and present situation of electric measuring instrument and features of intelligent meters are introduced in this paper. a brand - new scheme of intelligent electric parameter meter is proposed by the author after combining the features of intelligent meters and practical demand for electric measuring in 300mw generator units. general design, realization of hardware circuit comparison and analysis of errors of different algorisms are discussed in detail

    本論文介紹了電測儀表的發展歷史與現狀，以及新興智能儀表的特點；結合智能化儀表特點和300mw發電機組電參數測試的實際需要，首次提出了一種智能型發電機組電參數綜合測試儀的研究方案；詳細敘述了該智能型綜合測試儀的總體設計，硬體電路實現，各種演算法的比較的誤差分析；以及軟體框圖設計，針對影響測量精度的因素進行了分析，並制定了改進措施。
  20. This paper gives a research on the basic functions and their technical target of the catv field strength meter

    本文對有線電視場強儀應具備的功能，以及實現功能的技術指標進行了研究。
分享友人
分享到 Line

分享到臉書