milling property 中文意思是什麼

milling property 解釋
磨粉性質
  • milling : n 1 磨；制粉；碾碎。2 【機械工程】銑；銑削法；銑出的齒邊。3 軋貨幣的花邊，軋出的花邊；漿洗。4 〈...
  • property : n. 1. 財產；資產；所有物；所有地，地產；所有，所有權。2. 性質，特徵，屬性，特性；【邏輯學】非本質特性。3. 〈pl. 〉 【戲劇】道具；〈英國〉服裝。
  1. The effect of cutting speed, cutting thickness, cutting knife and materials on the working power capacity is discussed. finally tractive property of road plane milling machine is also studied. through the comparison of the results of theory calculation and experimental results the equation of working power capacity of milling machine is modified

    本文對冷式瀝青路面銑刨機的動力學工作過程進行了理論分析與試驗研究，並利用金屬材料切削的基本原理，研究了主切削力，並從能量轉化守恆的角度推導了銑刨機銑刨作業阻力和功率計算公式，討論了機器切削速度、銑刨厚度以及刀具與材料特性對銑刨作業阻力和功率的影響規律，最後討論了銑刨機牽引性能，且通過試驗研究驗證了銑刨作業阻力和功率公式。
  2. W - cu composites prepared from the precipitation w - cu powder have higher sintered density, better mechanical and physical property, more homogeneous and finer microstructure than those prepared from w - cu powder by the balling - reduction method. in chapter 5, a combination of homogeneous precipitation and ball - milling process, namely the mechano - thermochemical process was employed to prepare ultra - fine w - cu powder

    其中，球磨w一cu復合粉（ hp一m ）壓坯在1150下燒結30min后，可獲得相對密度大於99 %的幾乎全緻密的超細晶粒w一cu復合材料， w的顆粒度小於0 . 5林m 。
  3. Abstract : the relationship between milling technology and using properties in yak hair sweater were studied in this paper. based on the experiment, the size shrinkage, strength, warmth retention property and elasticity of elongation of eighteen different samples were discussed, and the relationship between these properties and milling factors were analysed. some rules were discovered

    文摘:研究了氂牛絨衫的縮絨工藝與其服用性能的關系.測試了經不同縮絨工藝處理后的18塊小樣的面積縮率、頂破強力、保暖率和拉伸彈性恢復率等指標.統計分析了縮絨工藝參數間關系，得到了一些規律
  4. By establishing the relationship between loss modulus and pan - milling, a empirical formula describing the pulverizing - dispersing property of polymer / filler blends brought about by pan - milling is suggested

    研究結果表明pp和wtr共碾磨有利於改善復合材料的加工流變性能和橡膠粒子在基體樹脂pp中的分散性。
  5. The cnc system can controls one nc milling machine with two shafts. it proves that the cnc system can do some basic interpolation movement. through adjusting the property of components, the cnc system can control one nc milling machine with three shafts to carry out some common machining tasks

    並利用這些可視化基本組件，組建了一個簡單的cnc系統，可以控制一臺二軸的數控銑床，進行基本的插補運動，還能調整組件屬性，控制一臺三軸的數控鉆銑床，進行一般的零件加工。
  6. The process of the high energy ball milling, the process of the flan press and the process of the liquid phase sinter was studied. and the influence of those processes to the property of the mo - cu alloy was concluded

    本文從工藝上主要研究了mo - cu復合粉末的高能球磨工藝、 mo - cu粉末生坯的壓制工藝、液相燒結工藝以及不同的工藝條件對材料性能的影響。
分享友人
分享到 Line

分享到臉書