mixed-flow 中文意思是什麼
mixed-flow
解釋
混流式-
Research and analysis of turbulent flow in mixed - flow bittern transfer pump
混流式輸鹵泵內部湍流場的研究 -
Study on process of rice concurrent - mixed flow drying
水稻順混流乾燥工藝的研究 -
Knudsen diffusion model and the mixed flow model were solved numerically for the ethanol - water system. good agreement between experimental and theoretical values was found. but the mixed flow model is better
乙醇水溶液的vmd試驗表明，兩種組分同時通過膜微孔時， knudsen擴散模型和過渡流模型都基本能反映實際過程，但過渡流模型更接近實際情況。 -
Volute mixed flow pump - part 2 : requirements
蝸殼式混流泵.第2部分:技術條件 -
Volute mixed flow pumps - part 1 : types and basic parameters
蝸殼式混流泵.第1部分:型式與基本參數 -
We are leading manufacturer and exporter of all kinds of blowers, including fan, centrifugal ventilator, axial - flow ventilator, mixed flow blower fans, boiler fans, electric welders, y series electric
排塵風機鼓風機，中壓風機排風扇工業強力風扇切 -
Theory calculation and derivation demonstrate that the heat conduction of membrane exerts little influence on performance. the characteristics of mass transfer through membrane are mixed flow including knudsen flow and poiseuille flow, which moreover, vary with operational variables
理論推導與計算表明：膜的導熱性對真空膜蒸餾過程的影響可以忽略，膜蒸餾過程膜內質量傳輸機制是努森流與粘性流共同作用的混合流機制。 -
Test methods for centrifugal, mixed flow, axial and regenerative pumps
離心泵混流泵軸流泵和旋渦泵試驗方法 -
Npsh for centrifugal, mixed flow and axial pumps
離心泵混流泵和軸流泵汽蝕余量 -
Diffuser mixed flow pump - part 2 : requirements
導葉式混流泵.第2部分:技術條件 -
Diffuser mixed flow pumps - part 1 : types and basic parameters
導葉式混流泵.第1部分:型式與基本參數 -
Centrifugal, mixed flow and axial pumps - code for hydraulic performance tests - precision class
離心泵混流泵和軸流泵水力性能試驗規范精密級 -
Economical operation for industrial centrifugal, mixed flow, axial flow and vortex pump systems
工業用離心泵混流泵軸流泵與旋渦泵系統經濟運行 -
Mixed flow and axial submersible pumps
混流式軸流式潛水泵 -
Industrial pumps. centrifugal, mixed flow and axial pumps. allowable level for mechanical vibrations
工業泵.離心泵混流泵和軸流泵.允許的機械振動級 -
An optimization design system has been constructed and practically used for centrifugal compressor components and mixed - flow pump impeller
目前，已經建立了離心壓氣機部件及水泵葉輪的優化設計系統，並在工程設計中發揮了重要作用。 -
Increasing capacity of mixed flow unit in shenwo hydropower station
參窩水電廠混流式機組的增容改造 -
Formation and recommendations of control method in urban traffic mixed flow
城市交通混合流的成因及其管制策略建議 -
On the basis of above theoretical derivation and analysis on experimental results, by correlating solvent ( water ) transfer with solute ( salt ) transfer on hot side and correlating mass transfer with heat transfer during vmd and introducing a contribution coefficient which can reflect the characteristics of mass transfer through membrane, a new model of mixed flow is presented
在上述理論推導及實驗分析的基礎上，本文將熱側溶劑傳輸與溶質傳輸、膜蒸餾過程熱量傳輸與質量傳輸相關聯，並引入一個能夠反映膜內質量傳輸特徵的「貢獻系數」 ，將努森流模型與粘性流模型結合起來，從而提出了新的混合流模型。 -
Three models are proposed as follows by applying the model of " mixed flow " : the stress of increasing fluid on fouling, collision between solid particles and fouling, and solid particles movement velocity ; the effects of operating parameters, properties of particles, and the volume fraction of particles on stress in solid - liquid two phase flow, collision stress between solid particles and fouling, maximal contacting area between solid particles and fouling and maximal contacting time between solid particles and fouling are investigated systematically by calculating and theoretical analysis
利用「混流」模型，建立了兩相流體的剪應力模型、固體顆粒與垢層的碰撞模型和固體顆粒的運動速度模型；通過計算和理論分析，系統地考察了操作參數、顆粒物性、顆粒體積分率等對固液兩相流剪應力、顆粒對垢層的碰撞力、顆粒與垢層的最大接觸時間和最大接觸面積的影響。
分享友人