neutral beam injection 中文意思是什麼

neutral beam injection 解釋
中性束注入
  • neutral : adj 1 中立的；中立國的。2 不偏不倚，公平的；中庸的；中間的；不倫不類的，不明確的；不鮮艷的，暗淡...
  • beam : n 1 梁，棟梁，桁條；（船的）橫梁。2 船幅；（動物、人的）體幅。3 （秤）桿，杠桿，（織機的）卷軸，...
  • injection : n. 1. 注射。2. 注射劑，注射液，針藥，灌腸（藥）。3. 充滿，注滿。4. 【醫學】充血。5. 【機械工程】噴射。6. 【宇宙空間技術】（衛星等的）入軌，射入軌道，射入軌道的時間[地點]。
  1. Liquid helium cryocondensation pump has great advantages in large pumping speed, working pressure range and high ultimate pressure, etc. it ' s more excellent than any other vacuum pump. it can meet the vacuum requirement of nbi and can improve the transportation efficiency. the development of neutral beam injection ( nbi ) system in the world, the structure of nbi system used on the ht - 7 device of asipp was introduced in the thesis

    液氦低溫冷凝泵是利用低溫面對氣體有強吸附能力的原理，實現抽氣的真空獲得設備，它具有抽速大、工作壓強范圍寬、極限真空度高等一系列優點，是普通真空設備無法比擬的，作為中性束注入系統的主抽泵，它能滿足中性束注入系統對大抽速的要求，提高中性束的傳輸效率。
  2. Neutral beam injection ( nbi ) heating is one of the main auxiliary heating methods in controllable nuclear fusion experiment

    中性束注入加熱是可控核聚變主要的輔助加熱方式之一。
  3. It is very significant for the research of nucleus fusion in resolving energy sources shortage, and neutral beam injection ( nb1 ) heating is one of the important assistant heating methods in nucleus fusion

    核聚變研究在解決當今能源短缺問題上具有十分重大的意義，中性束注入加熱是核聚變中重要的輔助加熱方式之一。
  4. The article primary introduces composing of ht - 7 neutral beam injection ( nbi ) system, then mainly analyzes gas target thickness, that is pressure distribution of neutralizer gas cell, one of factors which affect heating efficiency of nbi

    本文首先介紹了ht - 7中性束注入（ nbi ）加熱系統的組成，然後對影響中性束注入加熱效率因素之一的氣體靶厚度即中性化室的壓力分佈進行了重點分析。
  5. This paper introduces the neutral beam injection equipment that was the national chiefly supported project in 95 duration and mainly introduces the design and research of its computer monitoring and control system

    本文介紹了中國科學院等離子體物理研究所國家九五重點支持項目ht - 7中性束注入裝置監控系統的設計和研製。
  6. The research and studies on computer monitoring and control system in ht - 7 neutral beam injection equipment make sure to monitor and control the experimental process when the equipment runs in the closed environment

    開展中性束注入裝置監控系統的研究，確保該裝置在封閉運行的情況下對實驗過程進行遠程實時監控，具有十分積極的意義。
  7. This is a big complicated monitoring and control system, the article only discusses a part of the units, includes : the components of neutral beam injection and the requirements for monitoring and control system, the argumentation and selection of control scheme, the research of data acquisition system based on pci bus, the design and realization of hardware and software of dac, the means of concentrated data storage and management, the communication program design of subsystem under different mode and protocol. the last part gives some experiment system running data

    這是一個大型復雜的監控系統，本文只就其中的幾個單元的設計與實現展開討論，主要內容包括：中性束注入裝置的組成及其對監控系統的要求，監控系統控制方案的論證和選擇，基於pci總線的小型數據採集系統的研製，多功能數據採集卡的硬體和軟體的設計與實現，集中式數據存儲與管理的方法及其實現，多功能子系統之間在不同通信方式、不同傳輸協議下的通信實現及其程序設計。
  8. The theoretical analysis of large cryocondensation pump for nbi was mainly concerned. this paper emphasized on analyzing and calculating the heat load of cryocondensation pump, simulating thermal transmission coefficient and molecule transmission coefficient of radiation baffle according to monte carlo method, analyzing the process on cryo - surface and the factor of affecting pumping speed and hydrogen layer thickness of influencing cryo - parameter, etc. finally by verifying the pumping speed on large cryocondensation pump for neutral beam injection system, the pumping speed of 4. 0x105l / s ( for h2 ) was proven to be reasonable

    本文首先介紹了中性束注入系統的國內外發展狀況，闡述了中科院等離子體所ht - 7中性束注入系統的構成，主要對用於中性束注入系統的大型低溫冷凝泵的特性進行了理論分析；對冷凝抽氣面的熱負載進行了分析計算；用蒙特卡羅法對輻射擋板的分子傳輸幾率與熱傳輸幾率進行了模擬計算；研究了低溫表面的處理方法對抽速的影響以及氫層厚度對各低溫參數的影響；最後對用於中性束注入系統的大型低溫冷凝泵的抽速進行了驗證，得出的結論是：選取40萬升秒的抽速是合理的。
分享友人
分享到 Line

分享到臉書