normal tooth 中文意思是什麼

normal tooth 解釋
正常齒
  • normal : adj 1 正常的，平常的，普通的；平均的。2 正規的，標準的，額定的，規定的。3 智力正常的，精神健全的...
  • tooth : n （pl teeth）1 牙齒。2 齒狀突出，輪齒，鋸齒，耙齒（等）。3 嗜好。4 〈常 pl 〉（像牙齒那樣能咬人...
  1. Size and obliquity of tooth directly influence clutch whether normal operating. it is a key part for ensuring normal operating of aira too. this article fully deduces their compute formula

    該齒形的大小、傾角直接影響離合器是否能正確地嚙合和分離，也是保證機構進行正確工作的關鍵部分，本文詳盡推導了它們的計算公式。
  2. Tooth surface equations and contact line equations of the involute worm gearing are established according to its machining methodology. meshing characteristics in rigidity condition are studied. these characters include the inductive normal curvature along the contact line on the worm surface, the first and the second limit lines during the engage of the worm gear, and the influence of the intersect angle between the contact line the relative velocity of the worm and the gear on transmission performance

    根據漸開線圓柱蝸桿傳動的創成方法，建立了漸開線圓柱蝸桿和蝸輪的接觸線方程式、齒面方程式，分析了漸開線圓柱蝸桿傳動的剛性嚙合特性，如蝸桿與蝸輪嚙合時的誘導法曲率、一類界限曲線、二類界限曲線和蝸桿與蝸輪間相對速度方向和接觸線方向的夾角對傳動性能的影響； 2
  3. The results showed that the fracture of the tooth - razor was brittle fracture, the material quality was normal, the main fracture reson was that the carbide in the microstructure of the tooth - razor was distributed as reticulation, the brittleness of the razor was increased and the toughness was decreased, so the tooth of the razor was broken by external force when it was working

    結果表明，該剃齒刀的斷齒屬于脆性斷裂，主要是顯微組織中的碳化物分佈不均勻（呈網狀分佈） ，使刀具的脆性增大而強度、韌性下降，導致刀具在使用過程中由於外力的作用發生斷齒。
  4. The establishment of gear fault data warehouse the paper studies several gear cases in drive lab of wuhan university of science and technology. the signal of normal gear pair, the one has been worn seriously, the one which has circular pitch error and the one whose pinion has a ruptured tooth is acquired independently. after fft transformation, the amplitude values of 0 - 0. 4 multiple engage frequency, 0. 4 - 0. 5 multiple engage frequency, 0. 5 - 1 multiple engage frequency, 1 multiple engage frequency, 2 multiple engage frequency, 3 multiple engage frequency, 4 multiple engage frequency and greater then 4 multiple engage frequency of every signal are obtained respectively

    論文主要完成下列內容: 1 .齒輪故障數據倉庫的建立以武漢科技大學傳動實驗室的若干臺齒輪箱為研究對象，分別採集正常齒輪副、磨損嚴重的齒輪副、有周節誤差的齒輪副和小齒輪有一個斷齒的齒輪副的振動加速度信號，經過fft變換，分別得到每個信號的0 ~ 0 . 4倍嚙合頻率、 0 . 4 ~ 0 . 5倍嚙合頻率、 0 . 5 ~ 1倍嚙合頻率、 1倍嚙合頻率、 2倍嚙合頻率、 3倍嚙合頻率、 4倍嚙合頻率和大於4倍嚙合頻率幅值。
  5. Normal tooth profile

    法向齒廓
  6. By means of researching the meshing impact in the engagement of standard chain respectively with the spur toothed sprocket and the involute toothed sprocket, it has been discovered through analysis that by adopting the involute tooth for the sprocket could reduce the normal impact velocity in the engaging instant of chain and sprocket, thus lowered the meshing impact among chain and sprocket

    通過研究標準鏈條分別與直齒鏈輪和漸開線齒鏈輪嚙合的嚙合沖擊，分析發現在鏈輪上採用漸開線齒能減小鏈條與鏈輪嚙合瞬間的法向沖擊速度，進而降低鏈條與鏈輪的嚙入沖擊。
分享友人
分享到 Line

分享到臉書