normal working conditions 中文意思是什麼

normal working conditions 解釋
正常工作狀態
  • normal : adj 1 正常的，平常的，普通的；平均的。2 正規的，標準的，額定的，規定的。3 智力正常的，精神健全的...
  • working : adj 1 工作的，從事勞動的。2 操作的，作業的。3 工人的。4 （用於）實際工作的，任事的；使用（中）的...
  • conditions : （旅遊合同中）條件或服務項目
  1. The inner lining of such materials as br, nr, cr, fer, rpp, pvd, ptfe and f46 in the valve body of all kinds of cast iron and carbon steel or in the inwall of pipe castings can not only adapt to corrosion medium under different working conditions, but also can replace a great many rare and precious metal, which has, under the normal working conditions of valve, saved a large amount of funds for the users

    通過在各類鑄鐵、碳鋼的閥體或管件內壁上進行內襯br / nr / cr / fer / rpp / pvd / ptfe / f46等材料，不但可以適用於不同工況下的腐蝕性介質，而且可以替代許多稀有貴重金屬，為用戶在保證閥門正常使用的條件下節約大量的資金。
  2. But during the long time, middle - scale - cities planning and construction in roadway system have lack too much capital, and middle - scale - cities ca n ' t fit to the development of urban economic, so many problems have exposed. road transportation is the main components of the city function and basic facilities and is also the essential conditions of the city relying for existence, development maintaining normal working. at the present, the planning capacity is weak, and our research is only on big city ' s road planning, so it is necessary to study on the middle - scale - cities road system

    但是長期以來，中等城市道路系統的規劃建設欠賬太多，已不能適應城市經濟快速發展，暴露出許多問題。道路交通運輸是城市基本職能和物質基礎要素的重要組成部分，也是城市賴以生存、發展、維持正常運轉的必要條件之一。由於我國城市道路規劃起步較晚，規劃力量十分薄弱，目前主要精力集中在大城市的道路規劃與研究方面，因此，對中等城市道路系統的規劃發展作些探討已非常必要。
  3. As the electric power & electronic technology is used widely in low voltage area, the properties of voltage and current in normal working conditions of electrical appliance closely resemble or mimic the un - normal properties created by the arc fault, so it is difficult to distinguish between normal and un - normal cases

    隨著電力電子技術在低壓領域的廣泛應用，一些電器正常工作時的電壓電流特性與故障電弧的典型特性相似，給檢測工作帶來了難度。
  4. The definition of stability and repeatability of the laser frequency and factors affecting the stability of laser frequency were analysed. the normal methods used to stabilise frequency and produce double - frequency were explained. after analysing the working conditions and related parameters of the laser device, it was concluded that the laser tube should be put inside an insulating cover and an electric discharge tube with a bigger diameter and length, smaller wall thickness and a higher thermal conductivity coefficient should be chosen

    分析了激光頻率的穩定性、復現性的定義及影響激光頻率穩定的因素；介紹了常見的穩頻及產生雙頻的方法；分析論證了激光器雙縱模熱穩頻的使用條件和有關參數的關系，得到結論是：應將激光管裝在保溫罩內；選用放電管直徑及長度大、壁厚小、材料導熱系數大的放電管。
  5. Methods : according to x - rays of genu varum and genu valgum and cross - section ct of normal knee joint, 31 planar - models and 31 working conditions in three - dimensional finite element were established with the software of super - sap every 2 degree from genu varum 30 degree to genu valgum 30 degree, then calculated the stress and stain state of every node with the size and direction of actual stress

    方法：有限元模型的建立是利用膝關節內、外翻x線平片和正常人膝關節橫斷ct片，並用super - sap軟體分別建立平面和三維有限元模型，在內翻30至外翻30之間，每2按實際受力大小和方向加載，分別生成31個模型和31種工況，計算得出模型中各節點的應力應變情況。
  6. The damage causes according to the preliminary analysis are as follows : shortage of experience in domestic production ; too many and unsystematic manufacturing plant ; big differences of quality between products ; some manufacturing plants without production license ; one - sided understanding of the elastic metal plastic tile ; unlimited application of acting boundary lubrication as normal working conditions ; etc

    初步分析損壞的原因是：國內生產的彈性金屬塑料瓦在一開始缺乏經驗；生產廠家多而雜，產品質量良莠差異很大；有些廠家技術沒有過關就盲目組織生產；對彈性金屬塑料瓦的認識和宣傳片面，把邊界潤滑當作正常工況不加限制地應用等。
  7. The human resource system in dl office is supported by the head quarter located in chengdu. in normal conditions the working staff in dl office remained to be 80 persons, with every disciplines included

    Edri大連分院員工全部由總院調度和支持，但在大連分院常駐人員80多人並設置若干專業室
  8. No rise in temperature : the temperature will not increase as the materials are pulverized under the working conditions of pneumatic expansion and the temperature in the milling cavity is kept normal

    4不升溫，由於物料是在氣流膨脹狀態下粉碎，所以粉碎腔體溫度控制在常溫狀態，溫度不會升高。
分享友人
分享到 Line

分享到臉書