nozzle 中文意思是什麼

nozzle 解釋
n. 名詞 管嘴;噴嘴;〈俚語〉鼻子。
a jet [propelling] nozzle 【火箭】尾噴管。

  1. Transformers ; de - aerator with snow protection ; filling nozzle

    變壓器.防雪放氣裝置.注油塞
  2. Method of use : first dissolve the irrigation in solution as per the specified proportion, then push the irrigating nozzle to the focus, and place the absorbing tube into the solution bottle ; hold the air cell and pinch it repeatedly to wash the focus area with the solution passing through the nozzle

    使用方法:先將沖洗劑按規定比例化成溶液,沖洗咀推入患處,吸液管放入存放溶液的容器中,手握氣囊反復捏擠,沖洗液即可通過沖洗咀沖洗患處
  3. The nozzle flow is composed of the main gas stream and the secondary air stream in order to simulate the nozzle of turbofan engine

    噴管中的氣流由主流燃氣和次流空氣組成,用以模擬渦扇發動機的噴管。
  4. A convergent - divergent nozzle based burner and its numerical simulation

    縮放式噴管燃燒器及其數值模擬
  5. As the velocity in the nozzle throat is sonic, the effect must be transmitted upstream through the boundary layer.

    當噴管喉部達到音速時,這種影響一定是通過附面層向上傳播而引起的。
  6. A calculative formula and experimental study on loss - of - head of taper nozzle

    圓錐形噴嘴水頭損失的計算公式與試驗研究
  7. 14. no warranty will be delivered to such consumables as nozzle, cylinder body caulking, washer, seal ring, o - ring, motor brush, capacitor, bulb, fuse, battery, fan, belt, paper filter element, glass sheet, fuel and lubricant

    下列消耗品:噴油嘴缸體堵頭,墊片密封圈o型圈電機刷電容燈泡保險熔絲電池風扇皮帶紙濾蕊玻璃板燃油和潤滑劑。
  8. Performance of y - type airblast nozzle in solvent - removing process of chlorination liquid

    型氣流式噴嘴的霧化性能
  9. Closures for collapsible tubes are generally made of plastics materials today, and both thermosetting and thermoplastics types are available with a variety of external shapes and internal threads for screwing tightly on to tube nozzle

    當今, (裝)膏狀物小(金屬)管的管蓋通常由塑料材料製成,不管是熱硬化性塑料還是熱塑性塑料皆可,它們外型各異,並配有不同的內螺紋以保證管蓋與管口能擰緊。
  10. Finite element method was used for the calculation of temperature field, temperature gradient and thermal stress of the coal water slurry ( cws ) ceramic nozzle

    摘要採用有限元法對陶瓷水煤漿噴嘴溫度場、溫度梯度及其熱應力進行了分析計算。
  11. Results showed that the temperature, temperature gradient and thermal stress at the exit surfaces of the cws ceramic nozzle were higher than that of other part of the nozzle

    結果表明:在陶瓷水煤漿噴嘴的出口端面存在較大的溫度、溫度梯度和熱應力。
  12. Analog test study of nozzle width and split type ' s influence on pneumatic efflux element switching performance

    深寬比及劈高對氣動射流元件射流切換影響模擬試驗研究
  13. Its discovery engendered the "sudden freezing" approximation for relaxing nozzle flows.

    這一事實的發現導致了松馳噴管流動「突然凍結」的近似概念。
  14. Eustachian catheter nozzle

    咽鼓管導管嘴
  15. The machining, installation, debug of the nozzle are completed after its design, and the finial running results of the nozzle are provided

    在噴管結構設計完成後進行噴管加工、安裝、調試,最終給出噴管實際調試結果。
  16. The spray area of this series of nozzle is formed by one or several continuous hollow cone - shape rings of concentric circles. the nozzle aperture will not be blocked up. it is mainly used for flue elimination, cooling of steel - making convertor. and redistributing in all kinds of washing towers. it also can be used for jar cleaning. used in cooling tower and fire apparatus

    該系列噴嘴的噴霧區域是由一個或幾個連續的同心圓空心錐環組合而成,不易阻塞,主要用於煉鋼轉爐煙道除塵降溫及各種洗滌塔里的再分佈,也可用於清洗罐、冷卻塔、消防設備中。
  17. This " paper mainly researches on the humidifying property of the centrifugal nozzle with firing pin type, high pressure and little aperture

    課題主要對撞針型高壓小孔徑離心式噴嘴的霧化加濕性能進行研究。
  18. However, the related research is rarely reported on the humidifying property of the centrifugal nozzle with firing pin type, high pressure and little aperture

    但當前對該類型噴嘴加濕性能的相關研究還較少見諸報道。
  19. As to the work about theory analysis, at first, the paper describes the atomizing and humidifying process of the centrifugal nozzle with firing pin type, high pressure and little aperture and liquid physical properties. later, combining with the structure characters of this kind of nozzle, the paper studies on the theory of the atomizing and humidifying process by three phases, which is water film forming phase, water film falling into pieces phase, and heat and mass transfer between water and air phase in turn

    理論工作方面,首先描述了撞針型高壓小孔徑離心式噴嘴的霧化加濕過程和液體的物理性質,然後結合撞針型高壓小孔徑離心式噴嘴的結構特點,將其霧化加濕過程分三個階段進行機理上的研究,這三個階段依次為液膜形成、液膜初次破碎及二次霧化、水與空氣的熱濕交換。
  20. Based on the theory analysis and experiment work, the paper studies the humidifying property of the centrifugal nozzle with firing pin type, high pressure and little aperture. compared with the traditional air washer, the high efficiency and energy saving character of this kind of nozzle is stood out

    課題從理論和試驗兩方面分析研究了撞針型高壓小孔徑離心式噴嘴的霧化加濕性能,並將其與傳統噴水室加濕系統進行能耗比較,突出了撞針型高壓小孔徑離心式噴嘴高效節能的特點。
分享友人