operating pressure angle 中文意思是什麼
operating pressure angle
解釋
工作壓力角-
The following conclusions are gained : ( 1 ) the located shear band prongs the ligament near the top crack tip and the structure may occur shear - mode fracture at the angle of 155 ? to crack when load is 87. 92mpa ; the mode of fracture of the flange joint structure is not possible to be void - mode ; ( 2 ) it is proved that loading and then unloading repeatedly can not increase the possibility of invalidation of the structure when the times of loading and unloading are not too more when load is operating pressure ; the structure is safe when the vessel is operating ; ( 3 ) in the fe model of the thesis, not considering the influence of water pressure test which is in the process of fabrication of vessel in fe results in larger deviation in analysi
得出了以下結論：在8792mpa的載荷下筒體一封頭連接結構處的集中剪切帶貫穿韌帶，可能發生沿與原裂紋線成155 「角方向剪切型斷裂；筒體一封頭連接結構不可能發生韌窩型斷裂； （ 2 ）在工作壓力下進行次數不多的反復加、卸載，結構不會破壞，也不會喪失安定性：結構在工作狀態下是安全的； m在本文的彈塑性有限元模擬計算中，對于裂紋尖端進行力學分析時，不考慮壓力容器製造過程中水壓試驗的影響，將導致計算結果出現較大的偏差； （ 4 ）筒體完全屈服時的載荷為92石3mpa ，封頭完全屈服時載荷為86 -
The main achievements are as follows : the theory models of defect mfl field are set up ; based on the magnetic dipole model and finite element model, the distribution of defect mfl field is simulated in the dissertation ; the component of flux density ( magnetic filed ) parallel to the surface of pipe is detected by a circumferential array of hall probes ; the factors including defect geometry parameters, defect surface angle and shape, pipe material, field intensity, vehicle velocity, background magnetization, operating pressure and remanent magnetization and so on influence the mfl signal characteristics
採用霍爾元件作為缺陷漏磁檢測傳感器，獲得管道軸截面漏磁場切向分量的漏磁信號；研究了缺陷外形尺寸、缺陷傾角和形狀、管道材質和磁化強度、檢測儀移動速度、管道背底磁場、管內壓力和剩磁對漏磁信號的影響。提出了各通道增益放大、各路漏磁信號偏離調整、波形微分、數字濾波和平滑等漏磁信號預處理方法；分析了等空間采樣的漏磁信號轉換為等時間采樣信號的必要性，研究了漏磁信號的小波去噪方法。 -
To improve the transmitting characteristic and decrease the output work has a direct effect on the enhancement of the operating property and life - span of the operating mechanism of vacuum circuit breakes. based on the characteristics of polynomial rule of the cam movement, considering the pressure angle of cam device, an optimization model is established, with the coefficients of polynomial rule of cam movement as the optimizing variable, and the minimum output work of the mechanism as the object function. with the optimization tool box of matlab, the optimization process is conveniently completed and the perfect result of optimization design is obtained
改善真空斷路器操動機構的傳動運動特性，減小真空斷路器的操作輸出功，對提高真空斷路器的操作使用性能及壽命都具有直接的影響.利用凸輪機構的多項式運動規律的特點，以凸輪多項式運動規律的多項式系數為優化變量，以斷路器操動機構最小的輸出功為目標函數，考慮操動機構合分閘時凸輪機構傳動壓力角的情況，建立了彈簧操動機構中凸輪機構的優化數學模型，並利用matlab語言的優化工具箱方便地實現了優化過程，得到了較理想的優化設計結果 -
Operating pressure angle
工作壓力角
分享友人