optical engineering 中文意思是什麼

optical engineering 解釋
光學工程
  • optical : adj 眼的；視覺的；視力的；幫助視力的；光學（上）的。 optical activity 【物理學】旋光性。 an optic...
  • engineering : n. 1. 工程（技術），工程學。2. 開車技術。3. 土木工程，工事。4. 操縱，管理。
  1. Production in optical engineering - spherometer - ring for spherometer

    光學加工.球徑計.球徑計環
  2. Production in optical engineering ; lens block holders with inside fitting

    光學工程生產.用內配合件的鏡片塊夾具
  3. Production in optical engineering ; lens block holders with outside fitting

    光學工程的生產.帶外裝配件的透鏡片夾具
  4. Production in optical engineering - diamond impregnated cup wheels - part 1 : with steep cone

    光學加工.鑲金剛石的碗形砂輪.第1部分:帶圓錐體
  5. A monte carlo algorithm was presented to model the relation between the scattering phenomenon, depolarization changes and sea water depth, it is discovered that the radius of scattering point and the degree of depolarization increase with increasing of the sea water depth. at last, a optical engineering software ( lighttools ) is introduced to simulate optical scattering in the deep sea water, and studys the corelation between scattering and relative refractive index, particle density and particle size in the sea water. the experiment results show that the intensity of scattering will increase evidently with the increasing of particle size, particle density and relative refractive index. the methods and results in the article provide the basic theory and experiment validation for improving performance of communication, detection and imaging under sea water

    本文以球形粒子的mie散射理論、 stokes矢量法以及mueller矩陣來研究海水的散射特性和散射中的退偏振度變化;通過montecarlo方法模擬藍綠激光在海水傳輸過程中的散射現象以及散射中的退偏度變化與海水深度的關系，發現隨著海水深度的增加，散射后的光斑半徑、退偏振度將逐漸增大。最後通過光學工程軟體（ lighttools ）對海水中的散射進行模擬實驗，研究散射與海水中粒子密度、粒子大小和相對折射率的關系。實驗結果表明，隨著粒子半徑、粒子密度和相對折射率的增加，散射的強度將顯著增加。
  6. Production in optical engineering - diamond impregnated centering discs and discs with special profiles

    光學工程生產.鑲寶石的定心砂輪和特殊型面的砂輪
  7. Production in optical engineering - machine tool spindles - part 3 : hollow taper shank connection

    光學加工.機床軸.第3部分:中空錐柄連接
  8. Production in optical engineering - machine tool spindles - part 2 : machine tool spindles with clamping cylinder

    光學加工.機床軸.第2部分:帶夾緊缸的機床軸
  9. Qualified candidates must have a b. s. degree in electrical / mechanical / optical engineering ( m. s. preferred )

    應聘者需具有電子/機械/光學工程的學士及以上學位（碩士則更佳） 。
  10. Production in optical engineering ; ultrasonic cleaning machines ; areas for cleaning tanks

    光學技術加工.超聲波清洗機.清洗槽的面積
  11. Production in optical engineering - transport tray for spectacle lens production in rx workshops

    光學產品製造.配方車間眼鏡片傳送托盤
  12. Production in optical engineering - machine tool spindles - part 1 : machine tool spindles with steep taper

    光學加工.砂輪軸.第1部分:帶錐度的砂輪軸
  13. Production in optical engineering ; diamond impregnated pellets

    光學加工.鑲金剛石的片狀器材
  14. Production in optical engineering ; screwed connections without fitting part

    光學加工.無連接配件的螺紋連接件
  15. Production in optical engineering - diamond impregnated core drills - part 2 : with fitting cylinder

    光學工程生產.鑲金剛石的空心鉆.第2部分:帶裝配圓筒
  16. Shibin wu ( optical engineering ) directed by yapei yang ， jiahu yuan manufacturing technologies for large - aperture lightweight mirror are one of the development directions in advanced optical manufacturing technologies. the lightweight mirror has the incomparable advantages than that of the solid mirror. the lightweight mirror has overcome the mirror surface deformation caused by selfweight of the solid mirror, reduces or eliminates the deformation of thermal expansion in solid mirror surface induced by environmental temperature variations and temperature gradient appeared on mirror body. mechanical weight - reduction is one of the three lightening technologies for large - aperture mirror. the technology has the advantages of simple process, small technical difficulty, common equipment conditions and wide material selection range. the technology has been extensively investigated and applied in the technical field of optical engineering at home and abroad

    它克服了實心反射鏡因自重而引起的鏡面變形，降低或消除了實心反射鏡因環境溫度變化及鏡體溫採用機械鉆銑輕量化技術的輕型鏡研製度梯度的出現而產生的鏡面熱膨脹變形。機械減重輕量化技術是大口徑反射鏡輕量化技術的三種方法之一。它具有工藝簡單、技術難度較小、設備條件要求不高和選材范圍廣泛等優點，在國內外光學工程技術領域得到了廣泛的研究和應用。
  17. Production in optical engineering - diamond impregnated discs

    光學加工.鑲金剛石的切割鋸片
  18. Production in optical engineering - diamond impregnated cup wheels - part 7 : combinable shape grinding discs

    光學加工.鑲金剛石的杯形砂輪.第7部分:可組合的定形
  19. Production in optical engineering - block diameter 43 mm for manufacturing of ophtalmic lenses

    光學工程生產.眼鏡片製造用直徑43毫米的坯料
  20. Production in optical engineering - centering bells - part 3 : with cylindrical fitting dimension 12 mm and 25 mm for outer connection

    光學加工.定心罩.第3部分:外連接用圓柱形接頭.尺寸12
分享友人
分享到 Line

分享到臉書