orifice of pipe 中文意思是什麼

orifice of pipe 解釋
管口
  • orifice : n. （管子等的）口，孔，銳孔，【化學纖維】噴絲孔。
  • of : OF ＝Old French 古法語。
  • pipe : n 1 管，導管，筒。2 煙斗，煙袋；一袋煙。3 〈古語〉笛，管樂器；【航海】（水手長的）哨子（聲）；〈p...
  1. The structure and operating principle of an air - charged split - type adjustable shock absorber was described, e non - linear parameterized mathematical model of this shock absorber ' s damping characteristics was established according to fluid mechanics theory and the main structural affection factors to shock absorber ' s damping performance, such as the diameter of piston valve orifice, the diameter of adjustable orifice, the initial volume of gas chamber, the diameter of piston rod, the inner diameter of oil pipe and so on, were analyzed by simulations

    摘要通過分析一種分體式充氣可調阻尼減振器的結構和工作原理，運用流體力學理論，建立了該減振器阻尼特性的非線性參數化模型，模擬分析了活塞阻尼閥孔徑、阻尼調節孔徑、氣室初始體積、活塞桿直徑、油管內徑等主要結構參數對減振器阻尼性能的影響，通過試驗測試，得到了減振器樣件的阻尼特性及其可調范圍。
  2. ( 4 ) through the hydraulic property experiment of micro - hole lateral pipes of simple sdi in air, it was found that the average pressure of 60 mitre length lateral pipes was at the position of per 40o / o ~ ~ ~ 50 % of the effectual pipe length from the fist micro - hole, major pressure - loss was occurred at the ahead part of half pipe. the pressure uniformity reduced with orifice aperture ? increasing, and the relationship between pressure uniformity and initial water pressure was poor. running under the initial water pressure of 1. 5 meter, the discharge uniformity reduced with orifice aperture ? increasing, and when the orifice aperture smaller than or equal 1. 0mm, irrigation uniformity could achieve above 0. 6

    （ 3 ）通過對空氣介質中簡易地下滴灌的微孔毛管試驗研究發現： 60m管長的毛管平均壓力水頭的位置基本上在距第一孔口的有效管長40 - 45的地方；大部分水頭損失發生在毛管的前半部分；壓力均勻度隨孔徑的增大而減小，但與初始工作水頭關系不密切；在1 . 5m以下的工作壓力下運行，沿程出流均勻度隨孔徑的增大而降低，當孔徑不大於1 . 0mm時，灌水均勻度可以達到60以上；當孔徑大於等於1 . 2mm時，灌水均勻度低於50 。
  3. Length determine and installation of borehole orifice - pipe for grouting in the excavation face of shaft and drift

    井巷工作面注漿孔口管的長度確定與埋設
  4. Sgk - b250 plastic pipe belling machine attribute semiautomatic opportunities for the single - use. such models use infrared heating, molding method adopts expand the headers to finalize the design, orifice size precise shape. the control panel don ' t have the conversion switch to control over the type of solvent for expansion socket ( vertical ) and ring - for flexibility expansion socket ( r ). expanding way is very easy choice and technics adaptability is strong, the main electrical control components are imported, system performance is stable and reliable

    B250塑料硬管擴口機，屬半自動型作單機使用，擴管時管材由人工搬至擴管工位：這種機型採用紅外線加熱方式：成型方式均採用擴管頭定型方式，管口成型尺寸準確：該機型在控制面板上沒有擴溶劑型承插口（直口）和擴彈性密封圈型承插口（ r口）的轉換開關，擴管方式選擇十分方便，工藝適應性強：主要的電器控制元件均採用進口元件，系統性能穩定可靠。
  5. The research indicates that the orifice jet in mixing conditions has many different points from the pipe jet. focusing on the jet ejected from the orifices of different diameters and lengths, this paper studies the orifice jet when the fluid upstream of the orifices is in mixing conditions. the main purpose is to qualitatively study the effect of orifice diameters and lengths on the spread of the jet

    射流是在工程實際中廣泛存在的一種流動現象，噴嘴出口的流動狀態對射流的發展有很大的影響，前人對射流的研究主要集中於噴嘴前流體是完全發展管流的情形，本文研究了全混狀態下的板式射流，研究結果表明全混狀態下的板式射流具有很多不同於管射流的特點。
分享友人
分享到 Line

分享到臉書