orthogonal table 中文意思是什麼

orthogonal table 解釋
正交表
  • orthogonal : adj. 1. 直角的，互相垂直的；正交的；直交的。2. （統計數字）互不相關的。
  • table : n 1 桌子；飯桌，餐臺。2 手術臺；工作臺；游戲臺；賭臺；寫字臺。3 （飯桌上的）食物，酒菜，伙食；一...
  1. Under the different freezing - thawing cycle circumstance, three factors of water binder ratio, air content and mineral admixture are analyzed by using the method of orthogonal table. the test results show that the chief influencing factor is the water binder ratio in water freezing - thawing cycle circumstance, and in salt freezing - thawing cycle circumstance is the air content. this could illustrate that entraining air into concrete can improve the frost resistance of concrete effectively in salt freezing - thawing cycle

    分析了在純水和3 . 5 % nacl溶液中受凍后，水膠比、含氣量和摻合料對混凝土飽和系數及變化速率的影響規律，試驗結果表明水膠比對混凝土水凍時的飽和系數及變化速率影響顯著，而鹽凍情況下含氣量則是主要影響因素，說明引氣能顯著提高混凝土的抗鹽凍性能。
  2. Based on the pull - out tests data between geogrids and expansive soil / sands arranged by the orthogonal table l9 ( 34 ), the following conclusions are reached : 1 ) the displacement - properties of pullout tests depend on the pullout speed. the law of factors " affecting degree, which influences the parameters between geogrids and soils in the pulling - out procedure, is obtained. with the concept of " equivalent pull - out displacement ( x ) " brought forward, the whole process of pull out tests is divided into two process - " main process ( when x 1. 0 ) " and " residual process ( when x 1. 0 ) ", and three stages - static friction resistance stage, slip friction resistance stage, and residual friction resistance stage

    基於正交設計表l9 （ 3 ~ 4 ）分別安排了影響因素與土工格柵膨脹土或砂土界面相互作用參數的拉拔試驗數據，獲悉： 1 ）拉拔試驗位移特性主要取決于影響因素中拉拔速率；通過分析並獲取影響因素對筋土界面相互作用參數的影響程度及其在拉拔試驗過程中的變化規律，提出了當量拉拔位移（ x ）的概念，並據此將拉拔試驗全過程劃分成「主過程（ x 1 . 0 ） 」和「殘余過程（ x 1 . 0 ） 」 ；且將影響因素對拉拔力或摩擦阻力系數的影響程度分成三階段（靜摩擦阻力階段、滑動摩擦阻力階段，殘余摩擦阻力階段） ； 2 ）不同（規范）定義的筋土界面摩擦阻力系數數值相差較大，但影響因素對摩擦阻力系數影響程度及其變化規律不會因不同（規范）定義而受到影響。
  3. First of all, according to standard orthogonal table, 27 test samples in 9 groups are made, and the compressive strength has been measured in 28 days later

    採用正交試驗的方法對礦渣混凝土做了9組27個試塊，測出礦渣泥凝土28天的抗壓張度。
  4. This means the saturation degree of concrete is different. by means of analyzing the l9 ( 34 ) orthogonal table, the air content is the chief factor, the second factor is water binder ratio and the third is mineral admixture in both high water pressure and low water pressure. the water saturation degree of concrete in damaging point ( e6 / e0 = 60 % ) can be found by measuring the dynamic modulus of elasticity after six freezing - thawing cycles

    採用l9 （ 34 ）正交表對水膠比、含氣量和摻合料三個因素進行分析，試驗結果表明:在自然情況下，影響混凝土水飽和系數的主要因素是水膠比，而影響混凝土在鹽溶液中飽和系數的主要因素則是含氣量;在水壓力作用下，無論壓力大小，混凝土水飽和系數的影響次序依次為含氣量、水膠比、摻合料。
  5. By using the method of orthogonal table, the water binder ratio, air content and mineral admixtures which affect the saturation degree are analyzed in this paper. meanwhile in freezing and thawing cycle circumstance including water environment and 3. 5 % nacl liquor, the saturation degree and the saturation rate are also analyzed. moisture content of the concrete is different by varying water pressure

    本文採用正交分析方法，研究了自然飽水和壓力飽水條件下水膠比、含氣量和摻合料三個因素對混凝土飽和系數的影響規律，並研究了混凝土在純水和3 . 5 % nacl溶液中受凍后飽和系數的變化規律。
  6. Errors resulting from discrete sampling of zernike orthogonal ( space ) matrix is correct by error correction table. the edge detection precision is higher than 0. 1 pixels though signal to noise ratio up to 20db

    改進了zernike正交矩（空間矩）亞像素邊緣檢測演算法，用誤差修正表對離散采樣引起的誤差進行修正，使信噪比達到20db時，邊緣檢測精度仍然優於0 . 1像素。
  7. Based on the defect attributes of orthogonal defect classification proposed by ibm research center, a defect data table is designed and the specific flow of defect process is also given in the paper

    摘要基於ibm研究中心提出的正交缺陷分類屬性設計缺陷數據表格，並給出缺陷處理具體流程。
  8. The cubic orthogonal design is formed through the cubic orthogonal algorithm and neutral network and this algorithm is comprised with such models as select ing the cubic orthogonal table, establishing neutral network model, wavelets analyses processing and variance analyzing of the result, each model connected and mingled with each other

    智能正交設計是用立體正交演算法和神經網路演算法相結合而形成的；立體正交智能設計由下述模塊組成：選取立體正交表、建立神經網路模型、小波分析處理、結果方差分析等模塊，各個模塊彼此交融、互相連接。
分享友人
分享到 Line

分享到臉書