parallel diagnosis 中文意思是什麼
parallel diagnosis
解釋
并行診斷-
Through the simulation of large - scale circuit simulation proved that use the crossover tearing technology could detailed network structure, simplify the diagnostic process, and the neural network can parallel deal with the diagnosis information, and the logic operation can judge the information of the multi - fault. the illustrative simulation shows that it can increase the diagnosis speed and decrease the workload before test
通過對大規模模擬電路的模擬證明，使用交叉撕裂明細網路結構，簡化診斷過程，且運用神經網路組對信息進行并行處理，邏輯分析運算對多故障信息進行處理判斷，大大提高了故障診斷速度，減小了測前工作量。 -
Overvoltage breakdown of horizontal output valve in color tv set : parallel - connected capacitance method for diagnosis and theoretical analysis thereabout
逆程電容法對彩電行管過壓擊穿診斷及其分析 -
On the other hand, boundary - scan technique intelligent fault diagnostic method was applied to practice. for most digital system, devices with boundary - scan architecture are broadly used. only using four line or five line to connect pc parallel port with cut tap ( test access port ), all the ptvs can be loaded to cut and all homologous prvs can be taken back to intelligent fault diagnosis system
至於本文採用邊界掃描測試故障診斷技術，是考慮到本系統的通用性和簡潔性，因為對于大多數數字系統而言，具有邊界掃描結構的器件己廣泛應用，本文只需4條或5條信號線就能將pc機和被測邊界掃描電路連接起來，由此極大地簡化了智能故障診斷系統中為實現ptvs加載和prvs獲取而專門設計的介面板電路。 -
When those ptvs are sequentially loaded to cut ( circuit under test ) from intelligent fault diagnosis system, homologous prvs ( parallel response vector ) are taken back. through test response analysis by expert system, intelligent fault diagnosis system can detect all fixed ' 1 ' logic fault, fixed ' 0 ' logic fault, and detect the majority of multi - line short circuit fault
當這些ptvs從pc機中依次加載到被測電路板后，相應的prvs （并行響應向量集）可以獲取供診斷系統進行測試響應分析，從而檢測出固定邏輯故障和橋接故障。 -
Parallel relative model for the fault diagnosis of turbo - generator sets
汽輪發電機組故障診斷的并行關聯模型 -
Lift controller ' s fault diagnosis system ' s cost is largely reduced by using the board, which was replaced the parallel communication board
用它代替并行數據採集板，大大降低了系統的成本。 4 、設計並實現了電梯控制系統故障診斷軟體。 -
Abstract : the responses of shaft bow and their relationships with unbalanceresponses and mechanical or electronic run out are analyzed based on the theory of rotor dynamics. the responses of shaft bow are separated from the unbalance responses successfully by making use of vibration information under different rotor runs. an identification method of thermal bend is presented based on the 2d - holospectrum technique. experimental results show that when bow phase is steady and amplitude is variable, the tangent of initial phase point on the 2d - holospectrum is parallel, which can be effectively used for diagnosis of bent shaft
文摘:依據轉子動力學理論分析了柔性轉子彎曲響應的特徵，在此基礎上討論了它與不平衡響應及機械與電氣跳動量之間的關系，並利用轉子在不同起車情況下的振動信息，有效地分離了彎曲響應和不平衡響應，求解出彎曲量與不平衡量的比值.提出了轉子在恆定轉速下，基於二維全息譜技術的熱彎曲故障識別方法.研究結果表明，當彎曲量相位穩定而其幅值變化時，轉子響應的二維全息譜初相點的切線是相互平行的，由此可以有效地實現轉子熱彎曲故障的識別與診斷 -
Secondly, this paper discuss basic conception and general structure of expert system mainly, analyzes merits and faults of some algorithm deeply, on the basis of that, presents a fan fault diagnosis expert system based on rough sets theory by field reality. with the relation of fan ’ s symptom and fault, structures symptom - fault parallel table which is simple and clear. reduces knowledge base by rough sets, establishes inference rules through forward inference, overcomes the “ bottle neck ” problem of knowledge acquisition of expert system by combining fuzzy theory with rough sets
然後著重論述了專家系統的基本概念和一般結構，介紹了粗糙集理論的研究基礎以及在故障診斷中的應用，深入分析了幾種演算法的優缺點，在此基礎上結合現場實際構建了基於粗糙集的風機故障診斷專家系統的體系結構。利用風機徵兆和故障之間的關系構造了徵兆故障對照表，關系簡單明了。 -
This paper also established two kinds of expansion mode : structural inheritance and interface inheritance, which are called parallel expansion and additional expansion and are all based on character inheritance. through introducing the advantages of network calculation and great - volume storage, local cnc monitoring and diagnosis is expanded to lan, intranet and internet, and a multi - layer network activating monitoring and controlling model is established to realize the reasonable configuring and credible sharing of long - distance resources. to make re - development process more easy and friendly, a structural description language of cnc function character based on data library is designed for the target of inductive re - development mode
論文還提出了以基本cnc層+擴展cnc層為配置策略的開放式結構，通過區分平行擴展和補充擴展兩種形式，實現了開放cnc系統結構性繼承和介面性繼承的兩種新型擴展方案；探究將網路分佈計算和大容量存儲的技術優勢引入到現場監控應用中的具體方法，提出了本機監控、群控網路監控、企業車間監控和遠程監控為主體的四層監控診斷體系；獨創性地建立了一種網路分層激活的運轉機制，實現了網路資源的合理配置和可靠共享；建立了獨立的cnc系統二次開發環境，開創性地設計了一種以數控幾何工藝數據庫為基礎，以結構化的數控特徵語言描述為交互形式的引導型擴展配置方案。
分享友人