peak output current 中文意思是什麼

peak output current 解釋
峰值輸出電流
  • peak : vi 1 瘦弱；消瘦，憔悴。2 減少，縮小 （out）。n 1 山峰，山頂；孤山。2 （胡須等的）尖兒；尖端。3 最...
  • output : n. 1. 產量；生產，出產，產品。2. 【醫學】（糞便以外的）排泄物；排泄量。3. 【電學】發電力，輸出功率；供給量。4. 輸出信號。
  • current : adj. 1. 通用的，流行的。2. 現在的，現時的，當時的。3. 流暢的；草寫的。n. 1. 水流；氣流；電流。2. 思潮，潮流；趨勢，傾向。3. 進行，過程。
  1. We apply the agrawal ' s theory model of soa, and study the temporal characteristics of the output pulse for input picosecond optical pulses with different sharpness edges passing through a semiconductor optical amplifier, and find that the peak power and the pulse width of the output pulse depend on the input pulse peak power, the sharpness degree of the input pulse edge and the bias current of soa

    本文應用agrawal的關于soa理論模型，詳細研究了具有不同陡峭邊沿的皮秒超高斯光脈沖經soa后的時域特性的變化，發現輸出脈沖的峰值功率、脈沖寬度與輸入脈沖的峰值功率、輸入脈沖邊沿的陡峭程度以及soa的偏置電流密切相關。
  2. Design considerations of the high power s - band rka are described, by using electron beams of voltage - 600kv, current - 5000a, and the numerical simulations for three kinds of the rka output structures are given. the three kinds of the output strctures are single - gap standing - wave ( sw ) cavity, traveling - wave ( tw ) output structure, and two output structures ( single - gap + traveling - wave structure ). under conditions of using two output structures, the results show that the instantaneous peak power obtained from sw output cavity and tw output structure is respectively 2. 4gw and 2. 1gw, the both power average of 0. 96gw and 0. 93gw, i. e. the s - band rka of two output structures generates peak output power of 1. 89gw at a frequency of 2. 85ghz

    從數值模擬中得到雙輸出結構的微波功率輸出結果為:駐波輸出的瞬時功率為2 . 4gw （周期平均為0 . 96gw ） ;行波輸出結構輸出瞬時功率為2 . 1gw （周期平均0 . 93gw ） ，就獲得了頻率為2 . 85ghz的微波輸出。本文簡要的描述了電磁軟體（ magic ）對速調管輸出腔體進行了模擬，並對相應的模擬方法進行了評述。
  3. Different distribution of power loss can be worked out by mathcad software based on the formula reasoning. the result of calculation is consistent with that of the experiment, which proves that this method is right. it is pointed out through the analysis of calculating data that the key to improve efficiency at the same output power is to decrease the peak current and rms current of power switches or the on - resistance of mosfet and windings

    由推導可得損耗計算公式，利用數學計算軟體計算出電路輸出從空載到410w阻性負載時損耗分佈變化，該結果與實驗數據基本相吻合，證實了這種方法的正確性；通過對計算數據的分析，指出了進一步提高效率的關鍵在於輸出相同功率時降低功率管的電流峰值和有效值，減小繞組和mosfet的導通電阻。
  4. The results that increasing of bias current and shunted resistance and lowing critical current and connected inductance can decrease the transmission time are shown ; ( 4 ) a new type of circuit, ladder shape multiplayer jtl. structure is provided by author, thus output signal of rsfq circuits can be amplified before transfer to room temperature electronics system. it has highly gain of amplify relatively and the double peak structure are avoided through decreasing parasitic capacitance

    （ 4 ）針對目前超導與室溫介面電路的電壓放大器存在的「雙峰」和放大增益效率較低的不足，提出了一種全新的階梯式多層jtl電壓放大電路結構，較好的解決了以上的問題，通過初步的模擬分析證實，該電路的構思極負有創新性。
分享友人
分享到 Line

分享到臉書