piston chamber 中文意思是什麼

piston chamber 解釋
活塞頂內燃燒室
  • piston : n. 1. 【機械工程】活塞。2. 【音樂】(管樂器的)直升式活塞。
  • chamber : n 1 〈古、詩〉室,房間;寢室,臥室;〈pl 〉套房;〈pl 〉律師[法官]辦公室。2 會議室,會場;議會,...
  1. The structure and operating principle of an air - charged split - type adjustable shock absorber was described, e non - linear parameterized mathematical model of this shock absorber ' s damping characteristics was established according to fluid mechanics theory and the main structural affection factors to shock absorber ' s damping performance, such as the diameter of piston valve orifice, the diameter of adjustable orifice, the initial volume of gas chamber, the diameter of piston rod, the inner diameter of oil pipe and so on, were analyzed by simulations

    摘要通過分析一種分體式充氣可調阻尼減振器的結構和工作原理,運用流體力學理論,建立了該減振器阻尼特性的非線性參數化模型,模擬分析了活塞阻尼閥孔徑、阻尼調節孔徑、氣室初始體積、活塞桿直徑、油管內徑等主要結構參數對減振器阻尼性能的影響,通過試驗測試,得到了減振器樣件的阻尼特性及其可調范圍。
  2. When the governing valve was series - connected on the return oil - line in the metering - out control system, under the same flow area and the same adjusted pressure of relief valve, with the incremental quantity of step load, the pressure highly - adjusted capacity of the hydraulic cylinder chamber with piston - rod increased, meanwhile, it ' s time of rise, time to peak and the governing time all increased. at the same time, the pressure highly - adjusted capacity of the hydraulic cylinder chamber without piston - rod increased

    當出口節流調速系統的回油路上串接調速閥時,隨階躍負載的增加,在相同流量閥開度、相同溢流閥調節壓力的情況下,液壓缸有桿腔壓力p _ 2 ( t )的超調量是增加的,上升時間、峰值時間以及調整時間也是增加的;液壓缸無桿腔壓力p _ 1 ( t )的超調量是增加的。
  3. Simulation and analysis of the method of reducing thermal crack at the edge of piston with toroidal combustion chamber

    收口型燃燒室邊緣熱裂紋緩解措施的研究
  4. The piston moves up and down in the piston chamber primarily in response to changes in intake manifold vacuum.

    活塞主要因進氣歧管真空度的變化而在活塞腔內上下移動。
  5. When piston pump is applied force upward and movces, the lower check valve is opened, the fluid of upper pump chamber flows out of outlet when the piston runs upward

    當泵柱塞受力向上移動時,下止回閥打開,液體湧入下泵室中,泵進行進料的過程,上止回閥關閉,上泵室中的流體在柱塞上行時由出口端擠出。
  6. When pump is applied force downward and moves, the lower check valve is closed, the fluid in the pump is extruded and charges upward out of upper check valve, then flows into upper pump chamber, because that the piston has volume, some fluid flow out of outlet due to the reduce of spatial fluid volume in upper pump chamber

    當泵的柱塞受力向下移動時,下止回閥關閉,泵中的液體受擠壓而向上沖開上止回閥而流入上泵室中,由於柱塞本身佔有體積,部分的流體因上泵室內空間流體積的減少而自出口端流出。
  7. To withstand the heat of the combustion chamber, the piston must be strong

    為了禁得住燃燒室的高溫,活塞必須有足夠的強度。
  8. Detailed discussion on fea methods used in the coupling model of ic engine piston assembly and cylinder with the combination of the theoretic of fea, and theoretical foundation for two - and three - dimensional fea analysis of holistic coupling system of combustion chamber components

    結合有限元理論知識,詳細論述了在內燃機活塞組與缸套耦合模型中會用到的有限元方法。並為燃燒室部件整體耦合系統的二維、三維溫度場有限元分析奠定了理論基礎。
  9. The optimized combustion chamber accelerates the transferring speed of the flame, prevent the deflagrating, even the heat transfer on the piston and lower the amount of the exhausting gas

    優化設計的燃燒室,加快了燃燒過程中火焰的傳播速度,有效防止爆燃的產生,使活塞傳熱更加均勻,排放更低。
  10. Computerized cad programe system made csc cold chamber series out - stand of the producting die - casting. we unique designed all - in - one steel made figure and horizontal piston accumulator, especially for high quality die - casting produsts : copper, zinc and aluminum

    運用先進的cad電腦輔助設計系統,配合有豐富壓鑄經驗的技術專家,使csc系列冷室壓鑄機具備優異的性能。
  11. Accorded to the experimental research, under different flow area of flow valve and different adjusted pressure of relief valve, conclusion that the regulation of the pressure p1, p2 in the two cylinder chambers varied with the change of step load were as follows : when the throttle valve was series - connected on the return oil - line in the metering - out control system, under the same flow area and the same adjusted pressure of relief valve, with the incremental quantity of step load, the pressure highly - adjusted capacity of the hydraulic cylinder chamber with piston - rod decreased, meanwhile, it ' s time of rise, time to peak and the governing time all decreased. while the pressure highly - adjusted capacity of the hydraulic cylinder chamber without piston - rod increased

    通過試驗研究得出系統在不同的流量閥開度、不同溢流閥調節壓力(進口壓力)下,液壓缸兩腔壓力p _ 1 、 p _ 2隨階躍負載變化的規律:當出口節流調速系統的回油路上串接節流閥時,隨階躍負載的增加,在相同流量閥開度、相同溢流閥調節壓力的情況下,液壓缸有桿腔壓力p _ 2 ( t )的超調量是減小的,上升時間、峰值時間以及調整時間也是減小的;液壓缸無桿腔壓力p _ 1 ( t )的超調量是增加的。
  12. Piston brake chamber

    活塞式制動氣室
分享友人