plastic flow 中文意思是什麼

plastic flow 解釋
范性[塑性]流變。

  • plastic : adj 1 造型的；塑造的；給與形態的。2 可塑的，塑性的，受范的；柔軟的；〈比喻〉溫順的，肯聽話的。3 ...
  • flow : vi 1 流，流動。2 （血液等）流通，循環。3 流過；川流不息；（時間）飛逝；（言語等）流暢。4 （衣服、...
  1. This is portable pump with strong suction and medium head doss, equiped with extraordinary hair collector ; the body is made of themal plastic of strength ening fiberglass with good corrosive and impact resistance ; and with the advan tages of high flow, quiet

    這是一款輕便、自吸式、中等揚程的水泵、配有特大的毛發收集器；泵體由玻纖增強的工程塑料注塑而成；有良好的抗沖性和耐腐蝕性；此水泵具有高流量、運行安靜之優點。
  2. The mechanisms summarized are as follows 1 ) compressional normal stress ; 2 ) ductile and / or viscous deformation in bedding fault since incompetent bed is susceptible to plastic flow ; 3 ) higher likelihood of clay / shale smearing ; 4 ) foliation fabric whose sealing capacity is enhanced greatly in direction perpendicular to foliation

    其機理可歸納為四個方面： 1 ）壓性的正應力； 2 ）以韌性及粘性變形為主，因為非能幹巖層易塑性流變； 3 ）塗抹效應強； 4 ）面理化組構，垂直面理方向的封閉能力大大增強。
  3. Based on sale method ( simplified ale, in which the mesh may move with arbitrarily prescribed velocity with respected to the fluid, and lagrange interfaces are maintained between cells containing different material. ), the line loop integral difference scheme is derived which can be used to calculate two - dimensional elastic - plastic flow

    並在sale （ simplifiedale ，一種簡化的ale方法，網格可以任意運動，但物質界面處的網格仍然以物質速度運動，物質界面始終為lagrange網格線以保證網格中只有單物質出現）方法框架下，推導並給出了適用於彈塑性流計算的ale線積分差分格式。
  4. Check the length thickness ratio of the plastic flow

    檢查塑料流動的長度厚度之比
  5. Improper balance of plastic flow in multiple cavity moulds

    多模腔時塑料流動平衡不當
  6. The study on stability of plastic flow of alloy steel by spinning

    合金鋼旋壓塑流變形穩定性試驗研究
  7. Finite element analysis of casing damage in plastic flow formation

    塑性流動地層套管破壞的有限元分析
  8. Non - coaxial plastic flow theory in multi - dimensional stress state

    復雜應力狀態下巖土體的非共軸塑性流動理論
  9. The studies of material two - dimensional plastic flow in friction stir welding

    攪拌摩擦焊焊縫材料二維塑性流動研究
  10. Simulation of material plastic flow in aluminum alloy friction stir welding based on fluent

    的鋁合金攪拌摩擦焊流動場模擬
  11. Bingham plastic flow

    賓厄姆塑性流
  12. Plastic flow of steel

    鋼的塑流
  13. Plastic flow rule

    塑性憐規則
  14. This constitutive model describes the non - associated plastic flow of granular material, and replaces the assumption that granular material complies with associated flow rule in the limit " equilibrium theory of granular material

    該本構模型反映了散體材料的非相關塑性流動，取代了散體極限平衡理論中散體材料服從相關流動法則的假定。
  15. C. runner use plastic flow into the entire balanced design of bore elite left without end, the rapid - color

    C .流道採用全平衡入膠設計，內孔精拋，無死角，換色迅速。
  16. This control cabinet can control every point temperature in the hot runner, and keep a plastic flow at an optimum condition so that it is possible to avoid such defects as hollow and contraction cavity from lacking in supply, and to save materials and labor and reduce production costs at the same time. compared with ordinary, such hot runner will shorten the time of mould removal, carry out full - automatic ordinary, such hot runner will shorten the time of mould removal, carry out full automatic operation more easily, reduce the distance of mould - opening and the stroke of mould - closing

    使用本控制櫃能精確控制流道中各點溫度，使塑料流動達到最佳狀態，這樣能克服製件因補料不足而產生凹陷，縮孔等缺陷，同時節省了材料和人力，降低生產成本，與普通流道比脫模周期短，易實現全自動操作，可以縮短開模距與合模行程，縮短成型周期，可以成型較長製品。
  17. Standard test method for resistance to plastic flow of bituminous mixtures using marshall apparatus 6 inch - diameter specimen

    用馬歇爾儀器測試瀝青混合料的抗塑料流動性的標準試驗方法
  18. Based on the shale code, the early code of ale, the two dimensional finite difference elastic - plastic flow code hepale has been developed, in which the ideal elastic - plastic model and equation of state of gruneisen are used to describe the solid material, the programmed burn technique is used to simulate the propagation of detonation, and the equation of state of jwl is used to describe the detonation products

    藉助于ale方法的早期程序shale的基本框架，開發研製了二維彈塑性流ale方法計算程序hepale 。程序包含用彈塑性本構模型和gr nrisen狀態方程來描述固體材料的行為；採用jwl狀態方程來描述爆轟產物的性質；採用程序燃燒法來模擬爆轟波陣面的傳播。
  19. The predominant wear mechanisms of cu - nanosized tib2 in - situ composites are plastic flow and oxidational wear at higher sliding speed

    在較高滑動速度下，塑性流變和氧化磨損為其主要磨損機制。
  20. In this article, the reason how the friction produces in the process of metal forming was analyzed, and the friction was thought to be mainly caused by the plastic flow of metal in the pits of tool surface

    本文從微觀入手對金屬壓力成型過程中摩擦的形成原因進行了分析，認為摩擦主要是由於被壓入工具表面凹坑金屬的塑性流動所引起的。
分享友人
分享到 Line

分享到臉書