plating thickness 中文意思是什麼
plating thickness
解釋
板厚-
Since the dry plating does not require the reduction using electricity, the dry plating has many advantages in that it permits to plate the surface of non - conductive polymer materials, and further does not use the electrolyte solution so that wastewater is not produced and the plating thickness can be readily controlled
由於不要求用電還原,干鍍有許多優點,因為它允許對非導電性聚合物進行上鍍,其次不使用電鍍液,結果不產生廢水,而且鍍層厚度易於控制。 -
In order to solve the above - mentioned problems, the present invention provides a method for plating a polymer material with a metal film, which can form the film on the surface of polymer materials, which are difficult to plate by the prior wet plating method, at a relatively low cost in comparison to the dry plating method and exhibits a uniform thickness and a good adhesion of the metal film and further, shows a good reproducibility
為了解決上述問題,本發明提供了一種給聚合物材料上鍍金屬膜的方法,用該方法可以在聚合物材料表面形成膜層,這是原來的工藝難于做到的,而且比干鍍成本低,鍍層厚度均勻,金屬膜的粘附性好,最後,還顯示出好的重現性。 -
The thickness of the silver plating layer is in the range of 0. 2 m ~ 0. 5 m. through dta, it is proved that the metal plating layer is compatible with the substrate very well. the research on the testing of the complex decoy ' s properties is detailed below
該文還重點分析了影響鍍層導電性的因素;確定了鍍銀層厚度大致范圍在0 . 2 m 0 . 5 m ;通過差熱試驗,證實了鍍層金屬與基片是完全相容的性質。 -
Plating thickness must be held on this surface
此表面的鍍層厚度應該控制好。 -
Test methods of plating and coating thickness by beta backscattering for printed boards
印製板鍍塗覆層厚度測試方法反向散射法 -
Micro - resistance test method of plating thickness of plated through holes for printed boards
印製板金屬化孔鍍層厚度測定方法微電阻法 -
The capillary force can be dropped through vacuum drying process, and compact film with thickness of 6 u m was obtained by low spinning speed and few plating times
鍍膜次數較高時膜內易產生斷層。採用真空乾燥制度后通過低速少次就可以獲得厚度約為6 m的緻密膜。 -
The results showed that the deposition rate increases with the rise, of bath temperature and deposition thickness also increases as the plating time rises
實驗結果表明:化學鍍錫的沉積速度隨著溫度的升高而增加,沉積厚度也隨著時間的延長而增厚。 -
Aerospace series - cables, electrical, aircraft use - test methods - plating thickness
航空航天系列.飛行器用電纜.試驗方法.鍍層厚度 -
Aerospace series - cables, electrical, aircraft use - test mehtods - part 508 : plating thickness
航空航天系列.飛機電纜.試驗方法.第508部分:電鍍層厚度 -
Plating method, cylinder or matthews, depends on customer request, printing plate thickness could be appointed by customer
圓柱卷版方式或歐式matthews裝版方式,可依客戶要求製作。 -
The research results will lay the foundations for the design and manufacture of the multi - dimensional acousto - electropic - optic device. the thickness of plating layers and the length, width, thickness of piezoelectric transducer are determined, according to transporting line theory of mason ' s equivalent circuit
本文還利用傳輸線的瑪森等效電路理論確定各晶體在其工作模式下各鍍層的厚度及換能器的長度、寬度、厚度;研究結果為多維聲電光器件的設計與製作打下了良好基礎。
分享友人