polymer electrolyte 中文意思是什麼

polymer electrolyte 解釋
高分子電解質
  • polymer : n. 【化學】聚合體，聚合物，多聚物。 high molecular polymers 高聚物，高分子聚合物。adj. -ic
  • electrolyte : n. 電解質，電離質，電解（溶）液。
  1. Since the dry plating does not require the reduction using electricity, the dry plating has many advantages in that it permits to plate the surface of non - conductive polymer materials, and further does not use the electrolyte solution so that wastewater is not produced and the plating thickness can be readily controlled

    由於不要求用電還原，干鍍有許多優點，因為它允許對非導電性聚合物進行上鍍，其次不使用電鍍液，結果不產生廢水，而且鍍層厚度易於控制。
  2. In this article, the bellcore method was used to prepare polymer electrolyte membrane based on pvdf - hfp, and polymer electrolyte membranes under different conditions were prepared by changing sorts of solvents 、 ratio of dbp and solvent. effects of ratio of plasticizer and solvent on the liquid uptake 、 sem 、 mechanism capability 、 ionic conductivity 、 electrochemical stability window of polymer electrolyte membrane were also studied. through optimizing the preparation technics, the integrated effects of additives such as pc 、 ec 、 dbp and nanophase al2o3 on the ionic conductivity 、 liquid uptake were studied

    本文以聚偏氟乙烯-六氟丙烯共聚物pvdf - hfp為基質，採用bellcore制膜法制備了pvdf - hfp聚合物電解質膜，通過改變增塑劑dbp的含量、溶劑的種類及溶劑的含量制備了不同條件下的聚合物電解質膜，分別研究了增塑劑含量、溶劑含量等對聚合物電解質膜的吸液率、表面形貌、機械性能、離子電導率、電化學穩定窗口等的影響;對制備工藝進行了優化，研究了各種添加劑如pc 、 ec 、 dbp及納米al2o3對聚合物電解質膜的離子電導率、吸液率等性能的綜合影響。
  3. Gel polymer lithium batteries ( gplb ) not only have the excellent performance of liquid lithium battery, but also can resolve the possible problems of leakage and blast owing to no free liquid electrolyte in gplb. it is also very convenient to design the shape at will

    凝膠聚合物鋰離子電池不僅具有液態鋰離子電池的優良性能，而且由於電池中不存在游離的電解液，不但改善了液態鋰離子電池可能出現的漏液、爆炸等問題，外形設計也更加靈活方便。
  4. Firstly, a situ - polymerization method as the preparation process of gplb is introduced and pmma as the polymer matrix of the gel electrolyte is selected. the thermal polymerization process of the gel electrolyte is also optimized

    首先，採用了現場聚合法制備凝膠聚合物鋰離子電池的工藝，根據該制備工藝選擇pmma基作為該凝膠聚合物電解質的聚合物體系，然後對凝膠的熱聚合工藝進行了優化，確定了最佳的熱聚合工藝。
  5. Recent advances of all - solid - state polymer electrolyte systems that can be probably used in lithium ion batteries are reviewed, focusing on their electrochemical performances, especially the ionic conductivity at room temperature

    綜述了鋰離子電池聚合物常溫固體電解質的最新研究進展。主要關注的是電化學性能，尤其是室溫下的離子電導率。對性能較好的聚合物固體電解質體系進行了概述。
  6. The addition of pmma will reduce the crystallinity of blends and improve of the uptake of liquid electrolyte ( 260 % ) and the ion conductivity ( ims / cm ). at the same time the pvdf - hfp maintains the mechanical strength of blends film acting as polymer framework

    Pmma的加入可以降低共混體系的結晶度，提高共混物的電解液吸收能力（ 260 ）和離子電導率（ 1ms / cm ） ；同時pvdf - hfp起到骨架作用，使共混物膜具有足夠的機械強度。
  7. Solvents of dmac and nmp were used to prepare polymer electrolyte membrane, when the ratio of dbp and solvent was 20 %, both of the ionic conductivity can arrive at 10 - 3 s ? cm - 1, and the ionic conductivity of polymer made by nmp was 35 % higher than by dmac

    分別用溶劑dmac及nmp制備了聚合物電解質膜，在增塑劑與溶劑體積比為20 %時，聚合物膜的離子電導率均能達到10 - 3s ? cm - 1 ，且以nmp為溶劑的聚合物膜的電導率比以dmac為溶劑的電導率高出大約35 % 。
  8. The liquid uptake of polymer electrolyte membrane first increase, then remaining the same as the increasing of ratio of solvents. mechanism capability and ionic conductivity fist increase then decrease during the process, but it changed not much in total. through the test of sem it can be found that the structure of membrane changed little during the process

    在增塑劑含量及聚合物基質含量一定的條件下，隨溶劑含量的增大，聚合物膜的吸液率先增大后基本保持不變，機械強度及離子電導率則先增大后減小，通過sem測試可知，膜的表面形貌無明顯變化。
  9. Now the ion conductivity of gel polymer electrolyte ( gpe ) can reach the magnitude of 10 - 3s / cm, which can satisfy the practical request. however, it is still lower than that of liquid electrolyte ( 10 - 2 s / cm ), which causes the fall of high rate discharge and low temperature performance of lithium battery

    目前凝膠聚合物電解質（ gpe ）的室溫離子電導率可達10 ~ （ - 3 ） s cm數量級，已經能基本滿足應用的要求，但相比液態電解液的電導率（ 10 ~ （ - 2 ） s cm ） ， gpe的電導率仍然偏低，使得凝膠聚合物鋰離子電池的高充放電速率和低溫性能都大大的降低。
  10. With the development of solid polymer electrolyte, lithium and its alloys may be the promising anode materials

    隨著固體電解質的不斷研究，鋰金屬及其合金有可能成為最有前景的負極材料。
  11. Compared to liquid electrolyte, polymer solid electrolyte has greater develop protential as electrolyte material for lithium - ion secondary battery

    作為新型鋰離子電池的電解質材料，聚合物電解質的性能較液體電解質有更大的發展潛力。
  12. To test the validity of the model, hybrid inorganic / organic complementary ecd, comprising a tungsten oxide ( wo3 ) and polyanilinc ( pani ) thin film couple in combination with a proton - conducting polymer electrolyte, is studied

    為了要測試這個模型是否準確，對混合有機以及無機物的互補式電致色變元件進行研究，結合三氧化鎢和聚苯胺薄膜與導氫離子高分子電解質構成一互補式電致色變元件。
  13. The scientists dipped a polymer electrolyte film into a solution containing the virus, then into a solution of metal atoms, yielding a thin, transparent sheet coated in cobalt oxide and gold

    科學家把以高分子電解質製成的薄片插入含有病毒的溶液里，然後取出，再放入含有金屬原子的溶液，在薄片上面會產生出一個包覆著氧化鈷與金的透明薄膜。
  14. The emphasis is put on the electrochemical no ( subscript x ) sensors and the feasibility is dicussed for determination of nitrogen oxides using solid polymer electrolyte

    重點討論了氮氧化物電化學傳感器，並研究了利用固體聚合物作為電解質進行氮氧化物氣體檢測的可行性。
  15. By applying a voltage across the electrodes of a pixel, the polymer can be made to absorb or expel some of the electrolyte and thus expand or contract

    通過把一個像素的正負極輸入電壓，聚合物就能被加工成一種吸收或排除某些電解液的物質，這樣它也就會增大或縮小。
  16. This paper reviews the application of ionic liquids in polymer materials processing areas such as polymer electrolyte, the dissolution of polymer in ionic liquids, polymerization reactions in ionic liquids and plasticizing of polymer in ionic liquids

    綜述了離子液體在聚合物材料加工中的應用研究進展，主要包括聚合物電解質的合成應用研究、聚合物在離子液體中的溶解、以離子液體為溶劑的聚合反應以及離子液體作為聚合物的增塑劑。
  17. A gel - typed polymer electrolyte based on pvdf - hfp was studied

    本文研究了pvdf - hfp基鋰離子電池聚合物凝膠電解質的性質。
  18. The sort of polymer solid electrolyte materials for lithium - ion secondary battery, their conduction mechanism, performance and evolution were especially introduced

    重點介紹了鋰離子二次電池中聚合物電解質分類、導電原理、性能以及發展方向。
  19. Studies on ethylene catalytic sensor based on solid polymer electrolyte

    低溫固態電解質乙烯催化傳感技術研究
  20. Once in the polymer, the electrolyte stays there until a newly applied voltage coaxes it out

    一旦電解液被聚合物吸入，那這些液體就得待在裏面，直到新輸入的電壓把它們給排出去。
分享友人
分享到 Line

分享到臉書