position of symmetry 中文意思是什麼
position of symmetry
解釋
對稱位置-
Comparing and analyzing the synchronous control strategy, which brings up the new method to control the double un - symmetry jars proceed synchronously with the combination of proportional valve and servo valve, which forms closed loop control ; basing on the above methods, models are made to get mathematics models of position control system and to analyze system model theoretically by using pid controller, we can realize regulating parameters, minimizing synchronous errors and enhancing the dynamic performances ; the simulink tool box in matlab software is used to imitate the system according to the model, which not only makes the result visual and easy to adjust the parameters in interactive way but also lets us understand the effects of different parameters and optimizes the dynamic properties. the theory of plc control in dshp is discussed after advanced understanding of the system movements. hardware design and general regulation are given on the base of siemens company products s7 - 200 plc
本文根據大量的國內外文獻，對研配液壓機的工作原理及設計結構進行了簡介；對位置同步的控制方法進行了比較分析，提出比例閥和伺服閥復合控制的閉環結構來對非對稱雙缸進行同步控制電液比例同步控制方案；在此基礎上著重對比例閥控非對稱缸建模，最後得到位置控制系統的總體數學模型，從理論上對同步系統動態特性進行了分析，並用pid控制器進行參數整定，減小雙缸同步誤差、提高系統的動態響應性能；其中控制性能的分析藉助于matlab軟體中的simulink工具箱，由已建立的數學模型形成模擬模型，得到可視化的模擬結果，從而利於交互方式下調整參數，了解不同的參數對系統的影響，優化同步系統的動態性能；在深入了解系統的動作特性后，對plc控制研配液壓機的原理進行了探討，針對siemens公司s7 ? 200型plc給出了硬體設計的總體規劃，編制出研配液壓機動作控製程序，在編程中著重研究位移傳感器與plc的通訊、雙缸同步運行的pid控制在plc上的實現及bcd碼撥盤輸入程序的植入問題。 -
Welding position : if the configuration collocation of weld is symmetry and the welding sequence is reasonable, the longitudinal contraction and transverse lateral contraction deformation are usually produced, incontrast, the bending deformation is usually produced
焊接位置：如果焊縫在結構布置對稱，焊接順序合理時，則主要產生縱向收縮和橫向收縮變形，反之，則要發生彎曲變形。 -
Firstly, the basic character of the remote filed eddy current is simulated and analyzed in case of two - dimension axial symmetry which approves the existence of remote filed eddy current phenomenon ; the full circumferential defect model is investigated to approve the feasibility of using the rfec techniques to detect the position and depth of defect ; the pit corrosion 、 circumferential and axial crack models are simulated, and the defect character based on voltage plane polar plot and the changes of phase and amplitude are analyzed to supply the standard for defect reconfiguration
首先，在二維軸對稱情況下模擬與分析了遠場渦流的基本特性，證實了遠場渦流現象的存在;對全周向缺陷的遠場渦流檢測進行了詳細研究，證實了遠場渦流檢測缺陷位置和深度的可行性;對點狀腐蝕、軸向與周向裂紋三種非軸對稱缺陷進行三維有限元模擬，利用相位差和幅值變化曲線與電壓平面極坐標圖對缺陷特徵進行分析，為缺陷形狀重構提供了依據。
分享友人