positive end expiratory pressure中文意思是什麼

positive end expiratory pressure解釋
呼氣末正壓通氣

  • positive: adj 1 確實的,明確的;確定的;無條件的 (opp qualified implied inferential); 絕對的,無疑問的,...
  • end: n 1 端,尖,末端,終點。2 邊緣;極點,極限。3 結局,結果。4 目的。5 最後,死。6 【紡織;印染】經...
  • expiratory: adj. 吐氣的,呼氣的。 expiratory movement 深呼吸運動。
  • pressure: n 1 壓;按;擠;榨。2 【物理學】壓力,壓強;大氣壓力;電壓。3 精神壓力,政治[經濟、輿論等]壓力。4...

※英文詞彙positive end expiratory pressure在字典百科英英字典中的解釋。

  1. In view of bearing capacity of the elastoplastic theory analysis, the author made a comparison between the achieved bearing capacity limit load pi / 4 of round base ( space problem ) and the limit load pi / 4 of bar groundwork foundation design ( plane problem ) from soil mechanics at home and abroad as well as foundation criterion, and explained why the value of formula in present design criterion from soil mechanics is inclined to be conservative. in the light of the author ' s many years experience of vibration test on the spot and the research work of relevant projects, the author worked over the dynamic pile testing of the bearing capacity of foundation and batholith, and gathered the parameter of dynamic analysis and testing. the author also talked over the difficult point of pile foundation design criteria in present batholith engineering world, i. e. the confirmation of batholith bearing capacity of pile end, from the following aspects : a ) confirmation of single axis counter - pressure strength of rock in house ; b ) f. e. m calculation of elastoplastic model ; c ) calculation of soil mechanics ; d ) deep well load test

    然後,對巖土工程領域至今尚未解決,甚至不為人注意的考慮地基變形的地基承載力問題進行了實用化的探討,提出了考慮地基變形的地基承載力上程計算方法;對基於彈塑性理論分析的地基承載力國內尚未見報道的空間問題得到了圓形基礎(空間問題)的承載力界限荷載p _ ( 1 / 4 ) ,並與國內外土力學專著及地基基礎設計規范中的條形基礎(平面問題)的界限荷載p _ ( 1 / 4 ) ,進行了對比,從而定量上解釋了目前設計規范引用土力學承載力公式值偏於保守的這一情況;根據本文作者多年從事現場地基工程振動試驗及相關課題的研究工作,本文以截頭錐模型模擬地基,對地基(巖基)承載力的動測法進行了研究,為各類地基(包括巖基) ,匯總了動力分析和檢測川的參數:針對日前巖土工程界應用樁基設計規范中的難點? ?樁端巖基承載力的確定問題,從巖石室內單軸抗壓強度確定、基於彈塑性模型的有限單元法計算、土力學計算及深斤載荷試驗四方面進行了深入討論;本文作者根據多年現場載荷試驗的工程實踐,對深井荷試驗裝置的核心部分? ?反力裝置,設計了側壁支撐反力加載系統,該加載系統具有實用、簡便、穩定及安個等優點。
  2. Use connecting wire to connect the assembly black - white and brown bundle respectively to the positive end and negative end of ignition coil

    將總成黑白線、棕色線用轉接線束分別接至點火線圈正端和負端;
  3. This product is a full electron construction in which its front - end adopts pressure sensor with baffle filled oil chip. output signal is sent the data to microprocessor from high - precision, low temperature drift and high - reliability amplification circuit and a d convert circuit, after operating, to transform by high - precision d a convert circuit into standard signal output

    該產品為全電子結構,前端採用帶隔離膜充油芯體的壓力傳感器,輸出信號由高精度低溫漂和高可靠性的放大電路和模數轉換電路將數據送入微處理器,經運算後由高精度數模轉換電路變換為標準信號輸出。
  4. When the electrohydraulic push rod works, if the external force suffered by the piston rod is more than the setting output torque, the piston moves to the end ; oil pressure in the oil pipeline increases rapidly to the setting value, the safety valve overflows rapidly, to achieve overload protection

    電液推桿工作時,當活塞桿所受外力超過調定的輸出力距活塞運動到終點;油路中的油壓迅速增高至調定值,安全閥迅速溢流,實現過載保護。
  5. Function of three valve units is take signal from lead pressure point introduce the positive - negative pressure measuring container of transmitter, to realize on or off between lead pressure point and measuring container, and on off between positive and negative pressure container, also can use as differential pressure balance check zero and when remove transmitter as cut - off valve

    三閥組的作用是從引壓點將信號引入變送器的正負壓測量容室,實現引壓點與測量容室之間接通或斷開,以及正負壓測量容室之間接通或斷開,亦可作為差壓平衡檢測零點用和卸變送器時作截止閥用。
分享友人